Nissan Murano Z51. Manual — part 832
HA-44
< REMOVAL AND INSTALLATION >
LOW-PRESSURE PIPE
3.
Remove the mounting bolt (A), and then disconnect the low-
pressure flexible hose (1) from the low-pressure pipe (2).
CAUTION:
Cap or wrap the joint of the A/C piping with suitable mate-
rial such as vinyl tape to avoid the entry of air.
4.
Move the power steering reservoir tank to a position where it dose not inhibit work. Refer to
5.
Remove the mounting nut (A) and clip (B), and then remove the
low-pressure pipe (1) together with the low-pressure pipe
bracket (2).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
JPIIA0533ZZ
JPIIA0537ZZ
HIGH-PRESSURE PIPE
HA-45
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
HIGH-PRESSURE PIPE
Exploded View
INFOID:0000000005514548
HA-15, "Refrigerant Connection"
.
Removal and Installation
INFOID:0000000005514549
REMOVAL
1.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove the mounting bolt (A), and then disconnect the high-
pressure pipe (1) from the expansion valve.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve
with suitable material such as vinyl tape to avoid the entry
of air.
1.
High-pressure pipe
2.
O-ring
3.
Condenser assembly
4.
High-pressure flexible hose
5.
Compressor
6.
Low-pressure flexible hose
7.
Low-pressure pipe
8.
Heater & cooling unit assembly
9.
Evaporator pipe assembly
10. Expansion valve
11.
Evaporator
Refer to
JPIIA1257GB
JPIIA0538ZZ
HA-46
< REMOVAL AND INSTALLATION >
HIGH-PRESSURE PIPE
3.
Remove the mounting bolt (A), and then disconnect the high-
pressure pipe (1) from the condenser pipe assembly (2).
CAUTION:
Cap or wrap the joint of the A/C piping with suitable mate-
rial such as vinyl tape to avoid the entry of air.
4.
Move the power steering reservoir tank to a position where it dose not inhibit work. Refer to
5.
Remove the reservoir tank. Refer to
6.
Remove the washer tank inlet. Refer to
7.
Remove the clip (A), and then remove the high-pressure pipe (1).
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
• Replace O-rings with new ones. Then apply compressor oil to them when installing.
• Check for leakages when recharging refrigerant.
JPIIA0539ZZ
JPIIA0540ZZ
CONDENSER PIPE ASSEMBLY
HA-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
HA
N
O
P
CONDENSER PIPE ASSEMBLY
Exploded View
INFOID:0000000005514550
Removal and Installation
INFOID:0000000005514551
REMOVAL
1.
Use refrigerant collecting equipment (for HFC-134a) to discharge the refrigerant.
2.
Remove the front grille. Refer to
3.
Remove the mounting bolt (A), and then disconnect the high-
pressure flexible hose (2) and the high-pressure pipe (3) from
the condenser pipe assembly (1).
CAUTION:
Cap or wrap the joint of the A/C piping with suitable mate-
rial such as vinyl tape to avoid the entry of air.
4.
Remove the mounting bolt (A), and then remove the condenser
pipe assembly (1) from the condenser.
CAUTION:
Cap or wrap the joint of the A/C piping and condenser with
suitable material such as vinyl tape to avoid the entry of air.
1.
Condenser pipe assembly
2.
O-ring
3.
Condenser assembly
4.
Condenser lower bracket LH
5.
Bracket
6.
Liquid tank
7.
Refrigerant pressure sensor
8.
Liquid tank bracket
9.
Condenser upper bracket LH
10. Condenser upper bracket RH
Refer to
JPIIA0460GB
JPIIA0541ZZ
JPIIA0542ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст