Nissan Murano Z51. Manual — part 1456
TRANSAXLE ASSEMBLY
TM-175
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
When installing transaxle assembly to the engine assembly, attach
the fixing bolts in accordance with the following.
• When using the drive plate location guide (commercial service tool:
31197CA000) (A), set it to the stud bolts which is used to install it
to the torque converter.
• When not using drive plate location guide, rotate torque converter
so that the stud bolt (B) for mounting the drive plate location guide
of torque converter aligns with the mounting position of service
hole.
• Rotate crankshaft so that the hole (A) for inserting drive plate loca-
tion guide of drive plate aligns with the service hole (B).
NOTE:
When not using drive plate location guide, insert stud bolt of torque
converter into the hole (C) of drive plate, aligning the drive plate
hole position and torque converter.
CAUTION:
Be careful not to strike the drive plate when installing the
torque converter stud bolt.
• Align the position of tightening nuts (
) for drive plate with those
of the torque converter, and temporarily tighten the nuts. Then,
tighten the bolts to the specified torque.
CAUTION:
• When turning crankshaft, turn it clockwise as viewed from the
front of the engine.
• When tightening the nuts for the torque converter after fixing
the crankshaft pulley bolts, confirm the tightening torque of
the crankshaft pulley mounting bolts. Refer to
.
JPDIA0600ZZ
Insertion direction
Transaxle assembly to engine assembly
Engine assembly to tran-
saxle assembly
Bolt position
A
B
C
D
Number of bolts
1
2
2
4
Bolt length
mm (in)
55 (2.17)
39 (1.54)
108 (4.25)
45 (1.77)
Tightening torque
N·m (kg-m, ft-lb)
74.5 (7.6, 55)
50 (5.1, 37)
JPDIA0607ZZ
JPDIA0603ZZ
: 51 N·m (5.2 kg-m, 38 ft-lb)
SCIA1861E
TM-176
< UNIT REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
TRANSAXLE ASSEMBLY
• Rotate crankshaft several turns and check that transaxle rotates freely without binding after con-
verter is installed to drive plate.
• Never reuse O-ring.
• Apply grease to O-ring.
Inspection and Adjustment
INFOID:0000000005589458
INSPECTION BEFORE INSTALLATION
After inserting a torque converter to transaxle assembly, check that
dimension (A) is within the reference value limit.
INSPECTION AFTER INSTALLATION
Check the following.
• Check for CVT fluid leakage and check CVT fluid level. Refer to
.
• Check CVT position. Refer to
TM-159, "Inspection and Adjustment"
• Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Erase TCM data.
• Erase CVT fluid degradation level data. Refer to
TM-36, "CONSULT-III Function (TRANSMISSION)"
• When replacing the transaxle assembly, erase EEP ROM in TCM. Refer to
WHEN REPLACING CONTROL UNIT : Service After Replacing TCM and Transaxle Assembly"
B
: Scale
C
: Straightedge
Dimension A
: Refer to
JPDIA0620ZZ
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
TM-177
< UNIT DISASSEMBLY AND ASSEMBLY >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
UNIT DISASSEMBLY AND ASSEMBLY
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
Exploded View
INFOID:0000000005514129
Disassembly
INFOID:0000000005514130
1.
Remove transaxle assembly. Refer to
.
2.
Remove torque converter from transaxle assembly.
Assembly
INFOID:0000000005514131
Note the following, and install in the reverse order of removal.
• Attach the pawl (A) of the torque converter to the inner gear hole
(B) on the oil pump side.
CAUTION:
Rotate the torque converter for installing torque converter.
1.
Torque converter
2.
Transaxle assembly
JPDIA0691ZZ
JPDIA0692ZZ
TM-178
< UNIT DISASSEMBLY AND ASSEMBLY >
[CVT: RE0F09B]
TORQUE CONVERTER AND CONVERTER HOUSING OIL SEAL
Inspection
INFOID:0000000005514132
INSPECTION AFTER INSTALLATION
After inserting a torque converter to transaxle assembly, check
dimension (A) is within the reference value limit.
B
: Scale
C
: Straightedge
Dimension A
: Refer to
.
JPDIA0620ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст