Nissan Titan A60. Manual — part 290
TRANSFER CONTROL DEVICE
DLN-99
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
c. Tighten the bolts to the specified torque. Refer to
3. Install the breather hose to the transfer control device.
4. Connect the transfer control device connector.
5. After the installation, check the 4WD shift indicator pattern. If
NG, adjust the position between the transfer assembly and
transfer control unit. Refer to
DLN-84, "Precaution for Transfer
Assembly and Transfer Control Unit Replacement"
.
SDIA2212E
DLN-100
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
AIR BREATHER HOSE
AIR BREATHER HOSE
Removal and Installation
INFOID:0000000006179506
CAUTION:
• Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
• Install each air breather hose into the breather tube (metal
connector) until the hose end reaches the end of the curved
section. Set each air breather hose with paint mark facing
upward.
• Install transfer control device air breather hose and transfer
air breather hose on clip A and clip B with the paint mark fac-
ing upward.
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Breather tube (transfer)
7.
Air breather hose clamp
8.
Transfer control device
SDIA3351E
SDIA3340E
SDIA3353E
AIR BREATHER HOSE
DLN-101
< REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• Install clip C on transfer control device air breather hose and
transfer air breather hose with the paint mark matched.
• Install transfer control device air breather hose and transfer
air breather hose on clip D with the paint mark facing upward.
• Install transfer air breather hose (A) into the breather tube
(transfer, metal connector) until the hose end reaches the
base of the tube. Set transfer air breather hose with paint
mark (B) facing upward.
• Install transfer control device air breather hose into transfer
control device (case connector) until the hose end reaches
the base of the tube. Set transfer control device air breather
hose with paint mark facing forward.
SDIA3354E
SDIA3355E
AWDIA0784ZZ
SDIA3300E
DLN-102
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TX15B]
TRANSFER ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Removal and Installation
INFOID:0000000006179507
REMOVAL
1. Switch 4WD shift switch to 2WD and set transfer assembly to 2WD.
2. Remove the undercovers using power tool.
3. Remove the center exhaust tube and main muffler. Refer to
EX-5, "Removal and Installation"
4. Remove the front and rear propeller shafts. Refer to
DLN-132, "Removal and Installation"
141, "Removal and Installation"
CAUTION:
Do not damage spline, sleeve yoke and rear oil seal when removing rear propeller shaft.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
5. Remove the A/T nuts from the A/T crossmember. Refer to
TM-208, "Removal and Installation (4WD)"
6. Position two suitable jacks under the A/T and transfer assembly.
7. Remove the A/T crossmember. Refer to
TM-208, "Removal and Installation (4WD)"
.
WARNING:
Support A/T and transfer assembly using two suitable jacks while removing A/T crossmember.
8. Disconnect the electrical connectors from the following:
• ATP switch
• 4LO switch
• Wait detection switch
• Transfer control device
9. Disconnect each air breather hose from the following. Refer to
DLN-100, "Removal and Installation"
• Transfer control device
• Breather tube (transfer)
10. Remove the transfer to A/T and A/T to transfer bolts.
11. Remove the transfer assembly.
WARNING:
support transfer assembly with suitable jack while removing it.
CAUTION:
Do not damage rear oil seal (A/T).
INSTALLATION
Installation is in the reverse order of removal.
• Tighten the bolts to specification.
• Fill the transfer with new fluid and check for fluid leakage and fluid
level. Refer to
• Start the engine for one minute. Then stop the engine and recheck
the transfer fluid. Refer to
.
• After the installation, check the 4WD shift indicator pattern. If NG,
adjust the position between the transfer assembly and transfer
control unit. Refer to
DLN-84, "Precaution for Transfer Assembly
and Transfer Control Unit Replacement"
.
Tightening torque
: 36 N·m (3.7kg-m, 27 ft-lb)
SMT872C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст