Nissan Versa Note. Manual — part 709
B210C STARTER CONTROL RELAY
SEC-115
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
3.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connector E44 and clutch interlock switch connector E34.
2. Check continuity between IPDM E/R connector E44 and clutch interlock switch connector E34.
3. Disconnect BCM connector M98.
4. Check continuity between IPDM E/R connector E44 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
4.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connector F42 and transmission range switch connector F52.
2. Check continuity between IPDM E/R connector F42 and transmission range switch connector F52.
3. Disconnect BCM connector M98.
4. Check continuity between IPDM E/R connector F42 and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-70, "Removal and Installation"
NO
>> Repair or replace harness or connectors.
IPDM E/R
Clutch interlock switch
Continuity
Connector
Terminal
Connector
Terminal
E44
13
E34
2
Yes
IPDM E/R
Ground
Continuity
Connector
Terminal
E44
13
—
No
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
F42
40
F52
10
Yes
IPDM E/R
Ground
Continuity
Connector
Terminal
F42
40
—
No
SEC-116
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210D STARTER RELAY
B210D STARTER RELAY
DTC Logic
INFOID:0000000009705928
DTC DETECTION LOGIC
NOTE:
If DTC B210D is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210D displayed?
YES
>> Refer to
SEC-116, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705929
Regarding Wiring Diagram information, refer to
.
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210D CRNT?
YES
>> GO TO 2.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
2.
CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE
Check voltage between IPDM E/R connectors and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO (WITH M/T)>>GO TO 3.
NO (WITH CVT)>>GO TO 4.
3.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connectors E44, BCM connector M98, clutch interlock switch connector E34.
CONSULT Display
DTC Detection Condition
Possible Cause
STARTER RLY ON CIRC
[B210D]
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
ON position for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• Harness or connectors (starter motor relay
control circuit open or short)
• IPDM E/R
• BCM
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E44
13
—
Battery voltage
F42
40
B210D STARTER RELAY
SEC-117
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
2. Check continuity between IPDM E/R connector E44 and ground.
Is the inspection result normal?
YES
>> Refer to
NO
>> Repair or replace harness or connectors.
4.
CHECK STARTER CONTROL RELAY CONTROL CIRCUIT CONTINUITY
1. Disconnect IPDM E/R connectors F42, BCM connector M98, transmission range switch connector F52.
2. Check continuity between IPDM E/R connector F42 and ground.
Is the inspection result normal?
YES
>> Refer to
NO
>> Repair or replace harness or connectors.
IPDM E/R
Ground
Continuity
Connector
Terminal
E44
13
—
No
IPDM E/R
Ground
Continuity
Connector
Terminal
F42
40
—
No
SEC-118
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210E STARTER RELAY
B210E STARTER RELAY
DTC Logic
INFOID:0000000009705930
DTC DETECTION LOGIC
NOTE:
• If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• If DTC B210E is displayed with DTC B2605, first perform the trouble diagnosis for DTC B2605. Refer to
.
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210F may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210E displayed?
YES
>> Refer to
SEC-118, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705931
Regarding Wiring Diagram information, refer to
.
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210E CRNT?
YES
>> GO TO 2.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
2.
CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE
Check voltage between IPDM E/R connectors and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO (WITH M/T)>>GO TO 3.
CONSULT Display
DTC Detection Condition
Possible Cause
STARTER RELAY OFF
[B210E]
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
OFF position for 5 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• IPDM E/R
• BCM
• Battery
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E44
13
—
Battery voltage
F42
40
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст