Nissan Versa Note. Manual — part 708
B26FB CLUTCH SWITCH
SEC-111
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B26FB CLUTCH SWITCH
DTC Logic
INFOID:0000000009705920
DTC DETECTION LOGIC
NOTE:
• If DTC B26FB is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
• If DTC B26FB is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES >> Go
SEC-111, "Diagnosis Procedure"
NO
>> Inspection End
Diagnosis Procedure
INFOID:0000000009705921
1.
INSPECTION START
1. Turn ignition switch ON.
2. Select Self diagnostic result mode of BCM using CONSULT.
3. Touch ERASE.
4. Perform DTC CONFIRMATION PROCEDURE for DTC B26FB. Refer to
Is DTC detected?
YES
>> GO TO 2.
NO
>> Inspection End
2.
REPLACE ECM
EC-465, "Removal and Installation"
>> Inspection End
DTC No.
CONSULT screen items
(Trouble diagnosis content)
DTC detecting condition
Possible cause
B26FB
CLUTCH SWITCH
(Clutch switch)
BCM receives the abnormal signal of clutch
pedal position switch from ECM via CAN
communication.
• Harness or connector
(CAN communication line is
open or shorted)
• ECM
SEC-112
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B26FC KEY REGISTRATION
B26FC KEY REGISTRATION
DTC Logic
INFOID:0000000009705922
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
2. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> Go to
SEC-112, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705923
1.
REPLACE INTELLIGENT KEY
1. Prepare Intelligent Key that matches the vehicle.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
3. Check DTC in Self Diagnostic Result mode of BCM using CONSULT.
Is DTC detected?
YES
>> GO TO 2.
NO
>> Inspection End.
2.
REPLACE BCM
1. Replace BCM. Refer to
BCS-70, "Removal and Installation"
.
2. Perform initialization of BCM and registration of all Intelligent Keys using CONSULT. Refer to the CON-
SULT Immobilizer mode and follow the on-screen instructions.
>> Inspection End.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B26FC
KEY REGISTRATION
Intelligent Key that does not match the vehicle is
registered.
• Improper registration operation
• Intelligent Key
• BCM
B210B STARTER CONTROL RELAY
SEC-113
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210B STARTER CONTROL RELAY
DTC Logic
INFOID:0000000009705924
DTC DETECTION LOGIC
NOTE:
If DTC B210B is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210B displayed?
YES
>> Refer to
SEC-113, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705925
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210B CRNT?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
CONSULT Display
DTC Detection Condition
Possible Cause
START CONT RLY ON
[B210B]
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
ON position for 1 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• Transmission range switch signal input
IPDM E/R
SEC-114
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210C STARTER CONTROL RELAY
B210C STARTER CONTROL RELAY
DTC Logic
INFOID:0000000009705926
DTC DETECTION LOGIC
NOTE:
• If DTC B210C is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
.
• When IPDM E/R power supply voltage is low (Approx. 7 - 8 V for about 1 second), the DTC B210C may be
detected.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION
1. Turn ignition switch ON.
2. Turn ignition switch OFF and wait 1 second or more.
3. Turn ignition switch ON.
4. Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is DTC B210C displayed?
YES
>> Refer to
SEC-114, "Diagnosis Procedure"
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009705927
Regarding Wiring Diagram information, refer to
.
1.
PERFORM SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of IPDM E/R using CONSULT.
Is display history of DTC B210C CRNT?
YES
>> GO TO 2.
NO
>> Refer to
GI-41, "Intermittent Incident"
.
2.
CHECK STARTER CONTROL RELAY CONTROL CIRCUITS VOLTAGE
Check voltage between IPDM E/R connectors and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-31, "Removal and Installation"
NO (WITH M/T)>>GO TO 3.
NO (WITH CVT)>>GO TO 4.
CONSULT Display
DTC Detection Condition
Possible Cause
STR CONT RLY OFF CIRC
[B210C]
When comparing the following items, IPDM E/R
detects that starter control relay is stuck in the
OFF position for 1 second or more.
• Starter control relay signal (CAN) from BCM
• Starter relay status signal (CAN) from BCM
• Starter control relay and starter relay status
signal (IPDM E/R input)
• Starter control relay control signal (IPDM E/R
output)
• IPDM E/R
• BCM
• Battery
IPDM E/R
Ground
Voltage
(Approx.)
Connector
Terminal
E44 (WITH M/T)
13
—
Battery voltage
F42 (WITH CVT)
40
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст