Nissan Rogue. Manual — part 1211
TM-216
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
FLUID COOLER HOSE
• Refer to the followings when installing hose clamps.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Inspection
INFOID:0000000011279445
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
ALDIA0502ZZ
Fluid cooler hose (1)
Installation side
tube (2)
Hose clamp (3)
Direction of tab
Clamping position
Fluid cooler hose A
CVT oil warmer
Frontward
5 – 9 mm (0.20 –
0.35 in) (A) from
hose end
Radiator
Downward
Fluid cooler hose B
Radiator
Downward
CVT oil warmer
Upward
JSDIA2424ZZ
CVT OIL WARMER
TM-217
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CVT OIL WARMER
Exploded View
INFOID:0000000011279446
Removal and Installation
INFOID:0000000011279447
REMOVAL
WARNING:
Do not remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
engine coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter
turn to allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
1. Remove engine under cover. Refer to
.
2. Remove air duct. Refer to
EM-26, "Removal and Installation"
.
3. Remove fender protector side cover. Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
4. Disconnect water hoses from CVT oil warmer. Refer to
5. Disconnect fluid cooler hoses from CVT oil warmer. Refer to
.
6. Remove CVT oil warmer bolts (
) and remove CVT oil warmer
(1) from transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
Transaxle assembly
CVT oil warmer
: N·m (kg-m, in-lb)
JSDIA5055GB
JSDIA4162ZZ
TM-218
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
CVT OIL WARMER
Inspection
INFOID:0000000011279448
INSPECTION AFTER INSTALLATION
• Check for CVT fluid leakage and check CVT fluid level. Refer to
.
• Start and warm up the engine. Visually check that there is no leakage of engine coolant and CVT fluid.
PLUG
TM-219
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PLUG
Description
INFOID:0000000011279449
Replace the O-ring if oil leakage or exudes from the plug.
Exploded View
INFOID:0000000011279450
Removal and Installation
INFOID:0000000011279451
REMOVAL
1. Partially remove front fender protector (LH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
2. Remove the plug and O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection and Adjustment
INFOID:0000000011279452
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage. Refer to
.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
Transaxle assembly
O-ring
Plug
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: Apply CVT fluid
JSDIA3622GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст