Nissan Rogue. Manual — part 1025
COIL SPRING
RSU-13
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
13. Clean the mating surfaces of the wheel hub lock nut and the wheel hub and bearing.
CAUTION:
Do not apply lubricating oil to these mating surfaces.
14. Clean the mating surfaces of the joint sub-assembly and the
wheel hub and bearing. Apply Molykote M77 lubricant to the sur-
face (A) of the joint sub-assembly.
CAUTION:
Apply lubricant to cover the entire flat mating surface of the
joint sub-assembly.
NOTE:
Always check with the Parts Department for the latest parts
information.
15. Install the drive shaft to the wheel hub and bearing. Hold the wheel hub and bearing. Install the wheel hub
lock nut. Refer to
.
CAUTION:
• Since the drive shaft is assembled by press fitting, use a torque wrench to tighten the wheel hub
lock nut. Do not use a power tool.
• Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten
the wheel hub lock nut to the specification.
16. Install the cotter pin. Securely bend the cotter pin to prevent rat-
tles.
CAUTION:
Do not reuse cotter pin.
17. Install the rear wheel sensor to the axle housing. Refer to
BRC-131, "REAR WHEEL SENSOR : Exploded
.
CAUTION:
• Before installing, make sure there is no foreign material such as iron fragments adhered to the
pick-up part of the rear wheel sensor.
• When installing, make sure there is no foreign material such as iron fragments on and in the hole
in the axle housing for the rear wheel sensor. Make sure no foreign material has been caught in
the sensor rotor. Remove and foreign material and clean the mount.
18. Align the matching marks on the disc brake rotor and on the wheel hub and bearing. Install the disc brake
rotor.
19. Position the brake caliper on the disc brake rotor. Install the brake caliper torque member bolts. Refer to
BR-47, "BRAKE CALIPER ASSEMBLY : Exploded View"
20. Install the wheel and tire. Refer to
WT-67, "Removal and Installation"
21. Perform the final tightening of nuts and bolts under unladen conditions with tires on level ground.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust the neutral position of the steering angle sensor. Refer to
• Perform the sensor initialize of the headlamp aiming control system. Refer to
EXL-221, "SENSOR INITIALIZE : Special
(LED HEADLAMP).
JPDIG0122ZZ
JPDIF0295ZZ
RSU-14
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
REAR SHOCK ABSORBER
Exploded View
INFOID:0000000011276539
USA Production
Korea Production
1.
Rear suspension member
2.
Upper seat
3.
Coil spring
4.
Lower seat
5.
Arm bushing stopper (LH/RH) 6.
Rear suspension arm
7.
Rear shock absorber
Front
AWEIA0380ZZ
REAR SHOCK ABSORBER
RSU-15
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Removal and Installation
INFOID:0000000011276540
REMOVAL
1. Support the rear suspension arm using a suitable jack.
CAUTION:
Do not damage the rear suspension arm with the suitable jack.
2. Remove the rear shock absorber lower bolt and nut. Separate the rear shock absorber from the rear sus-
pension arm.
3. Remove the upper bolt, nut, and rear shock absorber.
INSPECTION AFTER REMOVAL
• Check rear shock absorber for deformation, cracks, damage. Replace it if necessary.
• Check welded and sealed areas for oil leaks. Replace it if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse the rear shock absorber nuts.
Perform the final tightening of nuts and bolts under unladen conditions with tires on level ground.
Disposal
INFOID:0000000011276542
1. Set rear shock absorber horizontally to the ground with the piston rod fully extracted.
1.
Rear suspension member
2.
Upper seat
3.
Coil spring
4.
Lower seat
5.
Arm bushing stopper (LH/RH) 6.
Rear suspension arm
7.
Rear shock absorber
Front
ALEIA0240ZZ
RSU-16
< REMOVAL AND INSTALLATION >
REAR SHOCK ABSORBER
2. Drill 2 – 3 mm (0.08 – 0.12 in) hole at the position ( ) from top
as shown to release gas gradually.
CAUTION:
• Wear eye protection (safety glasses).
• Wear gloves.
• Be careful with metal chips or oil blown out by the com-
pressed gas.
NOTE:
• Drill vertically in this direction (
) directly into the outer tube
avoiding brackets.
• The gas is clear, colorless, odorless, and harmless.
3. Position the drilled hole downward and drain oil by moving the piston rod several times.
CAUTION:
Dispose of drained oil according to the law and local regulations.
A:
20 – 30 mm (0.79 – 1.18 in)
JPEIA0161ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст