Nissan Rogue. Manual — part 1026
REAR SUSPENSION ARM
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION ARM
Exploded View
INFOID:0000000011276543
Removal and Installation
INFOID:0000000011276544
REMOVAL
1. Remove the wheel hub and bearing (FWD). Refer to
RAX-16, "Removal and Installation"
(FWD). Remove
the axle housing (AWD). Refer to
RAX-16, "Removal and Installation"
(AWD).
2. Remove the coil spring.Refer to
RSU-8, "Removal and Installation - FWD"
(AWD).
3. Separate the brake tube and hose from the rear suspension arm.
4. Remove the nut, bolt, rubber washer (LH/RH), and rear suspension arm.
INSPECTION AFTER REMOVAL
Visual Inspection
Check rear suspension arm and bushing for deformation, cracks or damage. Replace it if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse rear suspension arm nut.
• Verify that arm bushing stoppers are installed correctly with proper orientation.
• Align the matching marks made during removal when reusing the disc brake rotor.
• After installation, perform the air bleeding. Refer to
BR-16, "Bleeding Brake System"
.
• Perform the final tightening of the nuts and bolts under unladen conditions with the tires on level ground.
INSPECTION AFTER INSTALLATION
1. Adjust parking brake operation (stroke). Refer to
PB-4, "Inspection and Adjustment"
2. Check wheel alignment. Refer to
3. Adjust the neutral position of the steering angle sensor. Refer to
4. Perform the sensor initialize of the headlamp aiming control system. Refer to
IZE : Special Repair Requirement"
(HALOGEN HEADLAMP) or
EXL-221, "SENSOR INITIALIZE : Special
(LED HEADLAMP).
1.
Rear suspension arm
2.
Arm bushing stopper (LH/RH) 3.
Rear suspension arm bracket
4.
Rear suspension arm stay
Front
AWEIA0353ZZ
RSU-18
< REMOVAL AND INSTALLATION >
LOWER LINK
LOWER LINK
Exploded View
INFOID:0000000011276546
USA Production
Korea Production
1.
Rear suspension member
2.
Lower link
3.
Lower link deflector
4.
Arm bushing stopper (LH/RH)
5.
Rear suspension arm
ALEIA0206ZZ
LOWER LINK
RSU-19
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Removal and Installation
INFOID:0000000011276547
REMOVAL
1. Remove wheel and tire using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove rear stabilizer link. Refer to
3. Remove the bolts and separate the rear height sensor from lower link (if equipped). Refer to
4. Set suitable jack under rear suspension arm to relieve the coil spring tension.
5. Remove lower link, nut, and bolt from rear suspension arm with power tool.
6. Remove lower link, nut, washer, and bolt from rear suspension member with power tool.
7. Remove lower link deflector (if necessary).
INSPECTION AFTER REMOVAL
Check lower link and bushing for any deformation, cracks, or damage. Replace it if necessary.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse lower link nuts.
Perform final tightening of the nuts and bolts under unladen conditions with the tires on level ground.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust the neutral position of the steering angle sensor. Refer to
• Perform the sensor initialize of the headlamp aiming control system. Refer to
EXL-221, "SENSOR INITIALIZE : Special
(LED HEADLAMP).
1.
Rear suspension member
2.
Lower link
3.
Lower link deflector
4.
Arm bushing stopper (LH/RH)
5.
Rear suspension arm
ALEIA0241ZZ
RSU-20
< REMOVAL AND INSTALLATION >
UPPER LINK
UPPER LINK
Exploded View
INFOID:0000000011276549
USA Production
Korea Production
1.
Rear suspension member
2.
Upper link
3.
Arm bushing stopper (LH/RH)
4.
Rear suspension arm
Front
AWEIA0356ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст