Nissan Rogue. Manual — part 1024
COIL SPRING
RSU-9
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
11. Loosen the lower link nut at the rear suspension member. Remove the lower link bolt and nut from the
rear suspension arm. Separate the lower link from the rear suspension arm. Refer to
.
12. Separate the brake tube from the rear suspension arm. Refer to
.
13. Slowly lower the suitable jack supporting the rear suspension arm. Remove the upper seat, the coil spring
and the lower seat.
INSPECTION AFTER REMOVAL
Check lower link, bushing and coil spring for deformation, crack, and damage. Replace components if neces-
sary.
INSTALLATION
1. Align the lower seat indentations (C) with rear suspension arm
grooves (B). Install the lower seat protrusion (A) into the hole in
the rear suspension arm.
CAUTION:
The lower rubber seat protrusion must be securely inserted
into the hole of rear suspension arm.
2. Identify the upper side of the coil spring.
NOTE:
• The top of the coil spring has a flat shape.
• The paint identification mark (A) is 1.75 turns from the bottom
of the coil spring.
3. Align the coil spring (1) to the lower seat (2). Install coil spring to
lower seat.
CAUTION:
Assemble coil spring so that spring lower end is located in
the spring end holding section of lower rubber seat.
ALEIA0211ZZ
: Upper side
ALEIA0210ZZ
Maximum distance (A) : 5mm (0.20 in)
ALEIA0212ZZ
RSU-10
< REMOVAL AND INSTALLATION >
COIL SPRING
4. Align upper seat (2) to the body (1). Slowly raise the suitable
jack supporting the rear suspension arm to install the upper seat
to the body.
5. Install brake tube to rear suspension arm. Refer to
6. Install lower link with bolt and nut to the rear suspension arm. Refer to
NOTE:
The final tightening of nuts and bolts is under unladen conditions with tires on level ground.
7. Install upper link with bolt and nut to rear suspension arm. Refer to
.
8. Install rear shock absorber with bolt and nut to rear suspension arm. Refer to
9. Install height sensor (if equipped). Refer to
EXL-268, "Removal and Installation - Rear Height Sensor"
10. Install parking brake cable to rear suspension arm. Refer to
.
11. Install the stabilizer connecting rod. Refer to
12. Install the rear wheel sensor to the wheel hub and bearing. Refer to
.
CAUTION:
• Before installing, make sure there is no foreign material such as iron fragments adhered to the
pick-up part of the rear wheel sensor.
• When installing, make sure there is no foreign material such as iron fragments on and in the hole
in the wheel hub and bearing for the rear wheel sensor. Make sure no foreign material has been
caught in the sensor rotor. Remove and foreign material and clean the mount.
13. Align the matching marks on the disc brake rotor and on the wheel hub and bearing. Install the disc brake
rotor.
14. Position the brake caliper on the disc brake rotor. Install the brake caliper torque member bolts. Refer to
BR-47, "BRAKE CALIPER ASSEMBLY : Exploded View"
15. Install the wheel and tire. Refer to
WT-67, "Removal and Installation"
16. Perform the final tightening of nuts and bolts under unladen conditions with tires on level ground.
INSPECTION AFTER INSTALLATION
• Check wheel alignment. Refer to
• Adjust the neutral position of the steering angle sensor. Refer to
• Perform the sensor initialize of the headlamp aiming control system. Refer to
(HALOGEN HEADLAMP) or
EXL-221, "SENSOR INITIALIZE : Special
(LED HEADLAMP).
Removal and Installation - AWD
INFOID:0000000011276537
REMOVAL
1. Remove wheel and tire using power tool. Refer to
WT-67, "Removal and Installation"
2. Remove the bolt and separate the rear wheel sensor from the axle housing. Position the rear wheel sen-
sor and harness aside. Refer to
BRC-131, "REAR WHEEL SENSOR : Exploded View"
.
CAUTION:
• Failure to remove the rear speed sensor from the axle housing may result in damage to the rear
wheel sensor.
• Pull out the rear wheel sensor, being careful to turn it as little as possible. Do not pull on wheel
sensor harness.
3. Remove brake caliper torque member bolts using power tool, leaving the brake hose attached. Position
brake caliper aside with wire. Refer to
BR-47, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
ALEIA0213ZZ
COIL SPRING
RSU-11
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
Do not depress brake pedal while brake caliper is removed.
4. Put alignment marks on the disc brake rotor and on the wheel hub and bearing. Remove the disc brake
rotor.
CAUTION:
Do not drop disc brake rotor.
5. Remove the cotter pin.
6. Loosen, but do not remove, the wheel hub lock nut from the drive shaft using power tool.
7. Tap the wheel hub lock nut with a piece of wood and a suitable
tool to disengage the drive shaft from the wheel hub and bear-
ing.
CAUTION:
• Do not place the drive shaft joint at an extreme angle. Be
careful not to overextend the slide joint.
• Do not allow the drive shaft to hang without support.
NOTE:
Use a suitable puller if the drive shaft cannot be separated from
the wheel hub and bearing.
8. Remove the wheel hub lock nut.
9. Support the rear suspension arm using a suitable jack.
CAUTION:
Do not damage the rear suspension arm with suitable jack.
10. Remove stabilizer connecting rod. Refer to
.
11. Separate the parking brake cable from the rear suspension arm. Refer to
12. Separate the rear height sensor arm from the bracket (if equipped).
13. Remove the rear shock absorber lower bolt and nut. Separate the rear shock absorber from the rear sus-
pension arm. Refer to
14. Remove the upper link bolt and nut from the rear suspension arm. separate the upper link from the rear
suspension arm. Refer to
15. Loosen the lower link nut at the rear suspension member. Remove the lower link bolt and nut from the
rear suspension arm. Separate the lower link from the rear suspension arm. Refer to
.
16. Separate the brake tube from the rear suspension arm. Refer to
.
17. Slowly lower the suitable jack supporting the rear suspension arm. Remove the upper seat, coil spring
and lower seat.
INSPECTION AFTER REMOVAL
Check lower link, bushing and coil spring for deformation, crack, and damage. Replace components if neces-
sary.
INSTALLATION
1. Align the lower seat indentations (C) with rear suspension arm
grooves (B). Install the lower seat protrusion (A) into the hole in
the rear suspension arm.
CAUTION:
The lower rubber seat protrusion must be securely inserted
into the hole of rear suspension arm.
2. Identify the upper side of the coil spring.
NOTE:
• The top of the coil spring has a flat shape.
JPDIG0070ZZ
ALEIA0211ZZ
RSU-12
< REMOVAL AND INSTALLATION >
COIL SPRING
• The paint identification mark (A) is 1.75 turns from the bottom
of the coil spring.
3. Align the coil spring (1) to the lower seat (2). Install coil spring to
lower seat.
CAUTION:
Assemble coil spring so that spring lower end is located in
the spring end holding section of lower rubber seat.
4. Align the coil spring (1) to the upper seat (2). Install the upper
seat to the coil spring.
5. Align upper seat (2) to the body (1). Slowly raise the suitable
jack supporting the rear suspension arm to install the upper seat
to the body.
6. Install the brake tube to the rear suspension arm. Refer to
.
7. Install the lower link with the bolt and nut to the rear suspension arm. Refer to
NOTE:
The final tightening of nuts and bolts is under unladen conditions with tires on level ground.
8. Install the upper link with the bolt and nut to the rear suspension arm. Refer to
9. Install the rear shock absorber with the bolt and nut to the rear suspension arm. Refer to
10. Install the height sensor (if equipped). Refer to
EXL-268, "Removal and Installation - Rear Height Sensor"
.
11. Install parking brake cable to rear suspension arm. Refer to
.
12. Install the stabilizer connecting rod. Refer to
: Upper side
ALEIA0210ZZ
Maximum distance (A) : 5mm (0.20 in)
ALEIA0212ZZ
ALEIA0223ZZ
ALEIA0213ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст