Nissan Rogue. Manual — part 267
DAS
C1BB7-00 CONTROL MODULE
DAS-239
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BB7-00 CONTROL MODULE
DTC Description
INFOID:0000000011277402
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB7-00” detected?
YES
>> Proceed to
DAS-239, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277403
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB7-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BB7-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS-240
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BB8-00 CONTROL MODULE
C1BB8-00 CONTROL MODULE
DTC Description
INFOID:0000000011277404
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB8-00” detected?
YES
>> Proceed to
DAS-240, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277405
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB8-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BB8-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS
C1BB9-00 CONTROL MODULE
DAS-241
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BB9-00 CONTROL MODULE
DTC Description
INFOID:0000000011277406
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB9-00” detected?
YES
>> Proceed to
DAS-241, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277407
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB9-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BB9-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS-242
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BBA-00 CONTROL MODULE
C1BBA-00 CONTROL MODULE
DTC Description
INFOID:0000000011277408
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BBA-00” detected?
YES
>> Proceed to
DAS-242, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277409
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BBA-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BBA-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст