Nissan Rogue. Manual — part 265
DAS
C1BAB-00 STOP LAMP SWITCH
DAS-231
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
YES (“U1000-00”)>>Refer to
DAS-260, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> Inspection End.
DAS-232
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BB2-00 CONTROL MODULE
C1BB2-00 CONTROL MODULE
DTC Description
INFOID:0000000011277392
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB2-00” detected?
YES
>> Proceed to
DAS-232, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277393
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB2-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BB2-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS
C1BB3-00 CONTROL MODULE
DAS-233
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BB3-00 CONTROL MODULE
DTC Description
INFOID:0000000011277394
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB3-00” detected?
YES
>> Proceed to
DAS-233, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277395
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB3-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BB3-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
DAS-234
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BB4-00 CONTROL MODULE
C1BB4-00 CONTROL MODULE
DTC Description
INFOID:0000000011277396
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Trace Control function
• Active Ride Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB4-00” detected?
YES
>> Proceed to
DAS-234, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277397
1.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BB4-00” detected?
YES
>> Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BB4-00
CONTROL MODULE
(Control module)
When a malfunction is detected in chassis control module.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст