Nissan Rogue. Manual — part 373
DLK-334
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR LOCK AND UNLOCK SWITCH
Is the inspection result normal?
YES
>> Door lock and unlock switch is OK.
NO
>> Refer to
DLK-334, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000011279103
Regarding Wiring Diagram information, refer to
.
1.
CHECK POWER WINDOW SWITCH OUTPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage at the power window and door lock/unlock switch RH connector when the switch is
changed to “LOCK” or “UNLOCK”.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK POWER WINDOW SWITCH GROUND
1. Turn ignition switch OFF.
2. Disconnect power window and door lock/unlock switch RH connector.
3. Check continuity between power window and door lock/unlock switch RH connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK POWER WINDOW SWITCH
Check continuity between power window and door lock/unlock switch RH terminals.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace power window and door lock/unlock switch RH. Refer to
PWC-66, "Removal and Installa-
.
4.
CHECK POWER WINDOW SWITCH CIRCUITS
1. Disconnect BCM connector.
CDL UNLOCK SW
LOCK
: OFF
UNLOCK
: ON
Monitor item
Condition
Connector
Power window and door lock/unlock
switch RH state
Terminal
Voltage
(Approx.)
D112
Neutral
→ Lock
1
Ground
Battery voltage
→ 0
Neutral
→ Unlock
2
Power window and door lock/unlock switch RH con-
nector
Terminal
Continuity
D112
3
Ground
Yes
Power window and door lock/unlock switch RH state
Terminals
Continuity
Lock
1 - 3
Yes
Unlock
2 - 3
Neutral/Unlock
1 - 3
No
Neutral/Lock
2 - 3
2015 Rogue NAM
DOOR LOCK AND UNLOCK SWITCH
DLK-335
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
2. Check continuity between BCM connector and power window and door lock/unlock switch RH connector.
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK INTERMITTENT INCIDENT
GI-44, "Intermittent Incident"
.
>> Inspection End.
BCM connector
Terminal
Power window and door lock/unlock
switch RH connector
Terminal
Continuity
M18
10
D112
1
Yes
40
2
BCM connector
Terminal
Continuity
M18
10
Ground
No
40
2015 Rogue NAM
DLK-336
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
DOOR KEY CYLINDER SWITCH
DOOR KEY CYLINDER SWITCH
Description
INFOID:0000000011279104
When the mechanical key is inserted and turned into the front door lock key cylinder switch LH, the switch
transmits the LOCK or UNLOCK signal directly to the BCM.
Component Function Check
INFOID:0000000011279105
1.
CHECK FUNCTION
1. Select “DOOR LOCK” of “BCM” using CONSULT.
2. Select “KEY CYL LK-SW”, “KEY CYL UN-SW” in “Data Monitor”.
3. Check that the function operates normally according to the following conditions:
Is the inspection result normal?
YES
>> Door key cylinder switch is OK.
NO
>> Refer to
DLK-336, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000011279106
Regarding Wiring Diagram information, refer to
.
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES
>> Front door lock key cylinder switch LH is OK.
NO
>> GO TO 2.
2.
CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front door lock key assembly LH connector.
3. Check continuity between front door lock assembly LH connector and ground.
Is the inspection result normal?
Monitor item
Condition
Status
KEY CYL LK-SW
Driver side door key cylinder
Lock
ON
Neutral / Unlock
OFF
KEY CYL UN-SW
Unlock
ON
Neutral / Lock
OFF
Terminals
Key position
Voltage (V)
(Approx.)
(+)
(–)
BCM connector
Terminal
M19
92
Ground
Lock
0
Neutral / Unlock
8
93
Unlock
0
Neutral / Lock
8
Front door lock assembly LH connector
Terminal
Ground
Continuity
D23
4
Yes
2015 Rogue NAM
DOOR KEY CYLINDER SWITCH
DLK-337
< DTC/CIRCUIT DIAGNOSIS >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT
1. Disconnect BCM connector M18.
2. Check continuity between front door lock assembly LH connector and BCM connector M18.
3. Check continuity between front door lock assembly LH connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR KEY CYLINDER SWITCH
Check door key cylinder switch.
DLK-337, "Component Inspection"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Replace front door lock assembly LH. Refer to
DLK-384, "DOOR LOCK : Removal and Installa-
.
Component Inspection
INFOID:0000000011279107
COMPONENT INSPECTION
1.
CHECK DOOR KEY CYLINDER SWITCH
Check front door lock key cylinder switch LH.
Is the inspection result normal?
YES
>> Key cylinder switch is OK.
NO
>> Replace front door lock assembly LH. Refer to
DLK-384, "DOOR LOCK : Removal and Installa-
.
Front door lock assembly LH connector
Terminal
BCM connector
Terminal
Continuity
D23
6
M19
92
Yes
5
93
Front door lock assembly LH connector
Terminal
Ground
Continuity
D23
6
No
5
Terminal
Key position
Continuity
Front door lock key cylinder switch LH connector
6
4
Lock
Yes
Neutral / Unlock
No
5
Unlock
Yes
Neutral / Lock
No
2015 Rogue NAM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст