Nissan Rogue. Manual — part 914
MWI
MWI-3
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
METER CONTROL SWITCH . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
COMBINATION METER . . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
MWI-4
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000011279772
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
MWI
PREPARATION
MWI-5
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PREPARATION
PREPARATION
Commercial Service Tools
INFOID:0000000011279773
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
MWI-6
< SYSTEM DESCRIPTION >
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
METER SYSTEM
METER SYSTEM : Component Parts Location
INFOID:0000000011279774
Vehicle front
A.
View of the fuel pump and fuel level sensor inspec-
tion hole covers with the rear seat removed.
B.
View of front engine assembly
No.
Component
Function
1.
Seat belt buckle switch LH
Transmits the seat belt buckle switch signal LH to the combination meter.
2.
ABS actuator and electric
unit (control unit)
• Transmits each signal to the combination meter via CAN communication.
Refer to
MWI-8, "METER SYSTEM : System Description"
.
• Refer to
BRC-7, "Component Parts Location"
for detailed installation location.
3.
Washer fluid level switch
• Transmits the washer fluid level switch signal to the combination meter.
• Refer to
WW-6, "Component Parts Location"
for detailed installation location.
4.
Ambient sensor
• Transmits the ambient sensor signal to the combination meter.
5.
ECM
• Transmits each signal to the combination meter via CAN communication.
Refer to
MWI-8, "METER SYSTEM : System Description"
.
• Refer to
EC-14, "Component Parts Location"
for detailed installation location.
6.
TCM
• Transmits each signal to the combination meter via CAN communication.
Refer to
MWI-8, "METER SYSTEM : System Description"
.
• Refer to
TM-12, "CVT CONTROL SYSTEM : Component Parts Location"
for detailed installation
location.
ALNIA1644ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст