Nissan Rogue. Manual — part 978
PG
FUSE INSPECTION
PG-75
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
1. Turn the ignition switch OFF.
2. Turn the extended storage fuse switch OFF.
3. Press pawl and tilt to disengage the extended storage fuse
switch. Press pawl and tilt to remove the extended storage
fuse switch.
CAUTION:
Never use fuse for bus bar.
NOTE:
• Extended storage fuse switch and bus bar are removed together. Remove bus bar from extended stor-
age fuse switch, if necessary.
• Install removed bus bar to fuse block.
• Extended storage fuse switch is for transportation and storage. Reinstallation is not required after the
removal.
Type B
1. Turn the ignition switch OFF.
2. Turn the extended storage fuse switch OFF.
3. Hold and pull up the extended storage fuse switch hard in
direction.
CAUTION:
Never use fuse for bus bar.
NOTE:
• Extended storage fuse switch and bus bar may be removed together. Remove bus bar from extended
storage fuse switch, if necessary.
• Install removed bus bar to fuse block.
• Extended storage fuse switch is for transportation and storage. Reinstallation is not required after the
removal.
Type C
1. Turn the ignition switch OFF.
2. Turn the extended storage fuse switch OFF.
JSMIA0476ZZ
JSMIA0477ZZ
PG-76
< BASIC INSPECTION >
FUSE INSPECTION
3. Hold and pull up the extended storage fuse switch hard in
direction.
CAUTION:
Never use fuse for bus bar.
NOTE:
• Extended storage fuse switch and bus bar are removed together. Remove bus bar from extended stor-
age fuse switch, if necessary.
• Install removed bus bar to fuse block.
• Extended storage fuse switch is for transportation and storage. Reinstallation is not required after the
removal.
JSMIA0795ZZ
PG
FUSIBLE LINK INSPECTION
PG-77
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FUSIBLE LINK INSPECTION
Fusible Link
INFOID:0000000011280959
A melted fusible link can be detected either by visual inspection or by feeling with finger tip. If its condition is
questionable, use circuit tester or test lamp.
CAUTION:
• If fusible link should melt, it is possible that critical circuit (power supply or large current carrying
circuit) is shorted. In such a case, carefully check and eliminate cause of malfunction.
• Never wrap outside of fusible link with vinyl tape. Important: Never let fusible link touch any other
wiring harness, vinyl or rubber parts.
1
: Fusible link
JPMIA0516ZZ
PG-78
< REMOVAL AND INSTALLATION >
BATTERY
REMOVAL AND INSTALLATION
BATTERY
Exploded View
INFOID:0000000011280960
Removal and Installation (Battery)
INFOID:0000000011280961
REMOVAL
1. Pull back cover of battery positive terminal.
2. Loosen the battery terminal nuts and disconnect the battery negative and positive terminals.
CAUTION:
To prevent damage to the parts, disconnect the battery negative terminal first.
3. Remove battery frame nuts, battery frame and battery rods.
4. Remove battery cover and battery.
INSTALLATION
Installation is in the reverse order of removal.
WARNING:
Do not allow battery fluid to come into contact with skin, eyes, fabrics, or painted surfaces. After
touching a battery, never touch or rub your eyes until you have thoroughly washed your hands. If acid
contacts eyes, skin or clothing, immediately flush with water for 15 minutes and seek medical atten-
tion. Failure to do this may cause personal injury or damage to clothing or the painted surfaces.
1.
Battery frame
2.
Battery
3.
Battery rod
4.
Battery cover
5.
Battery tray liner
6.
Battery tray
Front
AWMIA1614ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст