Nissan Rogue. Manual — part 979
PG
BATTERY
PG-79
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CAUTION:
• Make sure battery tray liner is clean prior to installing new battery.
• To prevent damage to the parts, connect the battery positive terminal first.
• Make sure battery cables are tightly clamped to battery terminals for good contact.
• Check battery terminal for poor connection caused by corrosion.
Reset electronic systems as necessary. Refer to .
PG-72, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Special Repair Requirement"
Removal and Installation (Battery Tray)
INFOID:0000000011280962
REMOVAL
1. Remove battery. Refer to
PG-78, "Removal and Installation (Battery)"
.
2. Remove air duct. Refer to
3. Disconnect harness connector from TCM.
4. Remove wiring harness retainers.
5. Disconnect harness connectors from ECM.
6. Remove battery tray. Refer to
7. Remove TCM bracket from battery tray (if necessary).
8. Remove ECM bracket from battery tray (if necessary).
INSTALLATION
Installation is in the reverse order of removal.
• Reset electronic systems as necessary. Refer to
PG-72, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Special Repair Requirement"
• Perform the "Throttle Valve Closed Position Learning". Refer to
.
Battery terminal nut
: 5.39 N·m (0.55 kg-m, 48 in-lb)
PG-80
< REMOVAL AND INSTALLATION >
BATTERY TERMINAL WITH FUSIBLE LINK
BATTERY TERMINAL WITH FUSIBLE LINK
Exploded View
INFOID:0000000011280963
Removal and Installation
INFOID:0000000011280964
REMOVAL
1. Loosen battery terminal nuts and disconnect both negative and positive terminals from the battery.
CAUTION:
To prevent damage to the parts, disconnect the battery negative terminal first.
2. Disconnect positive cable from fusible link box (battery).
3. Disconnect harness connectors from fusible link box (battery) and remove fusible link box (battery).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the fusible link box battery if it has been dropped or sustained and impact.
To install the battery, carefully read the following instructions:
• To prevent damage to the parts, connect the battery cable to the positive terminal first.
• After connecting battery cables, to securely supply battery voltage, ensure that they are tightly
clamped to battery terminals for good contact.
• To securely supply battery voltage, check battery terminal for poor connection caused by corrosion.
Reset electronic systems as necessary. Refer to
PG-72, "ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL : Special Repair Requirement"
.
1.
Cover
2.
Positive terminal
3.
Battery
4.
Harness connectors
5.
Fusible link box (battery)
6.
Positive cable
Front
AWMIA1595ZZ
PG
SERVICE DATA AND SPECIFICATIONS (SDS)
PG-81
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Battery
INFOID:0000000011280965
*: Always check with the Parts Department for the latest parts information.
Type*
GR35
GR35
Capacity (20HR) minimum V-AH
12-60
12-63
Cold cranking current A @ -18
°C (0°F)
550
550
PWC-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
PWC
A
B
PWC
N
O
P
CONTENTS
POWER WINDOW CONTROL SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Work . . . . . . . . . . . . ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tools . . . . . . . . . ....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ..
Main Power Window And Door Lock/Unlock
Switch . . . . . . . . . . . . . . . . . ....
Power Window Switch RH . . . . . . . . . ....
Rear Power Window Switch . . . . . . . . . ..
Power Window Motor . . . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . ...
Fail Safe . . . . . . . . . . . . . . . . .
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) . . . . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
RETAINED PWR . . . . . . . . . . . . . ...
RETAINED PWR : CONSULT Function (BCM -
RETAINED PWR) . . . . . . . . . . . . ...
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) . . . . . . . ...
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
RETAINED PWR . . . . . . . . . . . . . .
RETAINED PWR : CONSULT Function (BCM -
RETAINED PWR) . . . . . . . . . . . . .
ECU DIAGNOSIS INFORMATION . . . ..
BCM (BODY CONTROL MODULE) . . . . .
List of ECU Reference . . . . . . . . . . . .
MAIN POWER WINDOW AND DOOR LOCK/
UNLOCK SWITCH . . . . . . . . . . .
Reference Value . . . . . . . . . . . . . ..
WIRING DIAGRAM . . . . . . . . . ..
POWER WINDOW SYSTEM . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . .
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORKFLOW . .
Work Flow . . . . . . . . . . . . . . . .
INSPECTION AND ADJUSTMENT . . . . ..
ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL . . . . . . . . ...
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Description . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT . . . . . . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description . . . . . . . . .
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст