Nissan Rogue. Manual — part 263

DAS

C1B95-00 CONTROL MODULE

DAS-223

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1B95-00 CONTROL MODULE

DTC Description

INFOID:0000000011277380

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended:

• Active Trace Control function

• Active Ride Control (brake) function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF

and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1B95-00” detected?

YES

>> Proceed to

DAS-223, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: Inspection End.

Diagnosis Procedure

INFOID:0000000011277381

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.

2. Turn the ignition switch OFF and wait for 10 seconds or more.

3. Turn the ignition switch ON.

4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1B95” detected?

YES

>> Replace the chassis control module. Refer to

DAS-286, "Removal and Installation"

.

NO

>> Inspection End.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1B95-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.

DAS-224

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1B99-00 CONTROL MODULE

C1B99-00 CONTROL MODULE

DTC Description

INFOID:0000000011277382

DTC DETECTION LOGIC

POSSIBLE CAUSE

• Chassis control module

FAIL-SAFE

The following functions are suspended:

• Active Ride Control function

• Active Trace Control function

• Active Engine Brake function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF

and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1B99-00” detected?

YES

>> Proceed to

DAS-224, "Diagnosis Procedure"

.

NO-1 >> To check malfunction symptom before repair: Refer to

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: Inspection End.

Diagnosis Procedure

INFOID:0000000011277383

1.

PERFORM SELF-DIAGNOSIS

With CONSULT

1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.

2. Turn the ignition switch OFF and wait for 10 seconds or more.

3. Turn the ignition switch ON.

4. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1B99” detected?

YES

>> Replace the chassis control module. Refer to

DAS-286, "Removal and Installation"

.

NO

>> Inspection End.

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1B99-00

CONTROL MODULE
(Control module)

When a malfunction is detected in chassis control module.

DAS

C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM

DAS-225

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C

D

E

F

G

H

I

J

K

L

M

B

N

P

A

C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM

DTC Description

INFOID:0000000011277384

DTC DETECTION LOGIC

POSSIBLE CAUSE

• ABS actuator and electric unit (control unit)

• Chassis control module

FAIL-SAFE

The following functions are suspended:

• Active Trace Control function

• Active Ride Control (brake) function

DTC CONFIRMATION PROCEDURE

1.

PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF

and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.

CHECK DTC DETECTION

With CONSULT

1. Turn the ignition switch OFF to ON.

CAUTION:

Be sure to wait of 10 seconds after turning ignition switch OFF or ON.

2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BA0-00” and/or “C1BA7-00”detected?

YES (“C1BA0-00”)>>Proceed to

DAS-225, "Diagnosis Procedure"

.

YES (“C1BA0-00” and “C1BA7-00”)>>Perform “Self Diagnostic Result” of “ICC/ADAS”.

NO-1 >> To check malfunction symptom before repair: Refer to

GI-44, "Intermittent Incident"

.

NO-2 >> Confirmation after repair: Inspection End.

Diagnosis Procedure

INFOID:0000000011277385

1.

CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SYSTEM

With CONSULT

Perform “Self Diagnostic Result” of “ABS”.
Is DTC detected?

YES

>> Check the DTC. Refer to

BRC-53, "DTC Index"

.

NO

>> GO TO 2.

2.

PERFORM SELF-DIAGNOSIS

With CONSULT

1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.

2. Turn the ignition switch OFF and wait for 10 seconds or more.

3. Turn the ignition switch ON.

4. Perform “All DTC Reading”.
Is DTC “C1BA0-00”, “U1000-00” or other DTC detected?

DTC

Display Item

(Trouble diagnosis content)

Malfunction detected condition

C1BA0-00

ADAS/CHASSIS CTRL BRAKE
SYS
(ADAS/Chassis Control brake
system)

• When receiving from ABS actuator and electric unit (control unit) that the value

of the brake system signal transmitted from the chassis control module to ABS
actuator and electric unit (control unit) is malfunctioning.

DAS-226

< DTC/CIRCUIT DIAGNOSIS >

[CHASSIS CONTROL]

C1BA0-00 ADAS/CHASSIS CONTROL BRAKE SYSTEM

YES (“C1BA0-00”)>>Replace the chassis control module. Refer to

DAS-286, "Removal and Installation"

.

YES (“U1000-00”)>>Refer to

DAS-260, "Diagnosis Procedure"

.

YES (other DTC)>>Check the DTC.

NO

>> Inspection End.