Nissan Rogue. Manual — part 264
DAS
C1BA2-00 STEERING ANGLE SENSOR
DAS-227
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BA2-00 STEERING ANGLE SENSOR
DTC Description
INFOID:0000000011277386
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Steering angle sensor
• Chassis control module
FAIL-SAFE
The following functions are suspended:
• Active Ride Control (engine) function
• Active Trace Control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BA2-00” detected?
YES
>> Proceed to
DAS-227, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277387
1.
CHECK STEERING ANGLE SENSOR SYSTEM
With CONSULT
Perform “Self Diagnostic Result” of “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “All DTC Reading”.
Is DTC “C1BA2-00”, “U1000-00” or other DTC detected?
YES (“C1BA2-00”)>>Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-260, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BA2-00
STEERING ANGLE SENSOR
(Steering angle sensor)
When a malfunction is detected in steering angle sensor system.
DAS-228
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BA2-00 STEERING ANGLE SENSOR
NO
>> Inspection End.
DAS
C1BA5-00 ADAS/CHASSIS CONTROL ENGINE SYSTEM
DAS-229
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1BA5-00 ADAS/CHASSIS CONTROL ENGINE SYSTEM
DTC Description
INFOID:0000000011277388
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Chassis Control Module
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BA5-00” detected?
YES
>> Proceed to
DAS-229, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277389
1.
CHECK ADAS CONTROL UNIT SYSTEM
With CONSULT
Perform “Self Diagnostic Result” of “ECM”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “All DTC Reading”.
Is DTC “C1BA5-00”, “U1000-00” or other DTC detected?
YES (“C1BA5-00”)>>Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
YES (“U1000-00”)>>Refer to
DAS-260, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> Inspection End.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BA5-00
ADAS/CHASSIS CTRL ENGINE SYS
(ADAS/Chassis control engine system)
• When receiving from ECM that the value of the engine system signal
transmitted from the chassis control module to ECM is malfunctioning.
DAS-230
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1BAB-00 STOP LAMP SWITCH
C1BAB-00 STOP LAMP SWITCH
DTC Description
INFOID:0000000011277390
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Stop lamp switch
• BCM
• Chassis Control Module
FAIL-SAFE
The following functions are suspended:
• Active Ride Control (engine) function
• Active Trace Control function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2. Perform “Self Diagnostic Result” of “CHASSIS CONTROL”.
Is DTC “C1BAB-00” detected?
YES
>> Proceed to
DAS-230, "Diagnosis Procedure"
NO-1 >> To check malfunction symptom before repair: Refer to
GI-44, "Intermittent Incident"
.
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis Procedure
INFOID:0000000011277391
1.
CHECK STOP LAMP SWITCH SYSTEM
With CONSULT
Perform “Self Diagnostic Result” of “BCM”.
Is DTC detected?
YES
>> Check the DTC. Refer to
(with Intelligent Key) or
(without Intelligent Key).
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1. Erase “Self Diagnostic Result” of “CHASSIS CONTROL”.
2. Turn the ignition switch OFF and wait for 10 seconds or more.
3. Turn the ignition switch ON.
4. Perform “All DTC Reading”.
Is DTC “C1BAB”, “U1000-00” or other DTC detected?
YES (“C1BAB-00”)>>Replace the chassis control module. Refer to
DAS-286, "Removal and Installation"
.
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1BAB-00
STOP LAMP SW
(Stop lamp switch)
When a malfunction is detected in stop lamp switch system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст