Nissan Rogue. Manual — part 138
BR-22
< REMOVAL AND INSTALLATION >
BRAKE PIPING
BRAKE PIPING
FRONT
FRONT : Exploded View
INFOID:0000000011279874
1.
Master cylinder secondary to
ABS actuator brake tube
2.
Master cylinder primary to
ABS actuator brake tube
3.
Brake tube bracket
4.
Brake tube (LH)
5.
Brake tube (RH)
6.
ABS actuator and electric unit
(control unit)
7.
ABS actuator to connector
brake tube (LH)
8.
ABS actuator to connector
brake tube (RH)
9.
Lock plate
10. Front brake hose
11. Union bolt
12. Copper sealing washers
13. Master cylinder
14. Connector bracket
15. Connector
A.
To front brake hose
B.
To rear brake tube
Front
ALFIA0440ZZ
BRAKE PIPING
BR-23
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
FRONT : Hydraulic Piping
INFOID:0000000011279875
FRONT : Removal and Installation
INFOID:0000000011279876
CAUTION:
• All hoses and piping (tubes) must be free from excessive bending, twisting and pulling.
• Make sure there is no interference with other parts when turning steering both clockwise and coun-
terclockwise.
• Do not spill or splash brake fluid on painted surfaces. Brake fluid may seriously damage paint. Wipe
it off immediately and wash with water if it gets on a painted surface.
• Do not allow foreign matter (e.g. dust) and oils other than brake fluid to enter the reservoir tank.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove reservoir cap from the reservoir tank.
2. Remove wheels and tires using power tool.
3. Loosen the flare nut with a flare nut wrench and separate the brake tube from the hose.
CAUTION:
• Do not scratch the flare nut and the brake pipe.
• All brake hoses and pipes must be free from excessive bending, twisting and pulling.
1.
ABS actuator and electric unit (con-
trol unit)
2.
Front disc brake
3.
Master cylinder assembly
4.
Brake booster
5.
Connector
6.
Rear disc brake
A.
Brake tube
B.
Brake hose
: Flare nut
: Union bolt
ALFIA0444ZZ
BR-24
< REMOVAL AND INSTALLATION >
BRAKE PIPING
4. Remove the union bolt (1) and the brake hose from the brake
caliper. Remove and discard the copper sealing washers.
CAUTION:
Do not reuse copper sealing washers.
5. Remove the lock plate and remove the brake hose.
INSTALLATION
CAUTION:
Do not allow foreign matter (e.g. dust) and oils other than brake fluid to enter the reservoir tank.
1. Assemble the union bolt (1) and the copper sealing washers to
the brake hose and install it as an assembly to the brake caliper.
Align the brake hose pin to the projection (A) by aligning it with
the brake caliper hole, and tighten the union bolt (1) to the spec-
ified torque.
CAUTION:
Do not reuse copper sealing washers.
2. Install the brake pipe to the brake hose, temporarily tighten the flare nut by hand until it does not rotate fur-
ther, and attach the brake hose to the bracket with the lock plate.
CAUTION:
Check that the brake hoses and pipes are not bent or twisted.
3. Tighten the flare nut to the specified torque with a flare nut crowfoot and a torque wrench.
CAUTION:
Do not scratch the flare nut and the brake pipe.
4. Refill with new brake fluid and perform the air bleeding. Refer to
BR-16, "Bleeding Brake System"
.
CAUTION:
Do not reuse drained brake fluid.
5. Install the wheels and tires. Refer to
WT-67, "Removal and Installation"
6. Perform inspection after installation. Refer to
REAR
JPFIA0099ZZ
JPFIA0099ZZ
BRAKE PIPING
BR-25
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR : Exploded View
INFOID:0000000011279877
REAR : Hydraulic Piping
INFOID:0000000011279878
1.
Rear brake pipe assembly (RH)
2.
Rear brake pipe assembly (LH)
3.
Lock plate
4.
Rear brake hose
5.
Union bolt
6.
Copper sealing washers
A.
To brake pipe connector
B.
To rear brake hose
Front
ALFIA0443ZZ
1.
ABS actuator and electric unit (con-
trol unit)
2.
Front disc brake
3.
Master cylinder assembly
4.
Brake booster
5.
Connector
6.
Rear disc brake
A.
Brake tube
B.
Brake hose
ALFIA0444ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст