Nissan Rogue. Manual — part 137
BR-18
< PERIODIC MAINTENANCE >
FRONT DISC BRAKE
FRONT DISC BRAKE
Brake Burnishing
INFOID:0000000011279870
CAUTION:
• Burnish contact surfaces between brake pads and disc brake rotor according to the following proce-
dure after refinishing the disc brake rotor, replacing brake pads or if a soft pedal occurs at very low
mileage.
• Be careful of vehicle speed. Brakes do not operate firmly/securely until pads and disc brake rotor are
securely seated.
• Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive the vehicle on straight, flat road.
2. Depress the brake pedal until the vehicle stops.
3. Release the brake pedal for a few minutes to allow the brake components to cool.
4. Repeat steps 1 to 3 until pad and disc brake rotor are securely seated.
REAR DISC BRAKE
BR-19
< PERIODIC MAINTENANCE >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
REAR DISC BRAKE
Brake Burnishing
INFOID:0000000011279871
CAUTION:
• Burnish contact surfaces between brake pads and disc brake rotor according to the following proce-
dure after refinishing the disc brake rotor, replacing brake pads or if a soft pedal occurs at very low
mileage.
• Be careful of vehicle speed. Brakes do not operate firmly/securely until pads and disc brake rotor are
securely seated.
• Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive the vehicle on straight, flat road.
2. Depress the brake pedal until the vehicle stops.
3. Release the brake pedal for a few minutes to allow the brake components to cool.
4. Repeat steps 1 to 3 until pad and disc brake rotor are securely seated.
BR-20
< REMOVAL AND INSTALLATION >
BRAKE PEDAL
REMOVAL AND INSTALLATION
BRAKE PEDAL
Exploded View
INFOID:0000000011279872
Removal and Installation
INFOID:0000000011279873
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-23, "Removal and Installation"
.
2. Remove the knee protector. Refer to
.
3. Remove snap pin and clevis pin from clevis of brake booster.
4. Disconnect the harness connectors from the stop lamp switch and brake pedal position switch.
5. Remove the accelerator pedal. Refer to
ACC-3, "Removal and Installation"
.
6. Remove the brake pedal.
CAUTION:
Support the brake booster and master cylinder to prevent contact with other components.
INSPECTION AFTER REMOVAL
• Check the following items and replace the brake pedal assembly if necessary.
- Check the brake pedal rivet for deformation or damage.
- Check the brake pedal for bend, damage, and cracks on the welded parts.
1.
Rivet
2.
Clevis pin
3.
Brake pedal
4.
Brake pedal pad
5.
Clip
6.
Snap pin
7.
Stop lamp switch
8.
Brake pedal position switch
AWFIA1074ZZ
BRAKE PEDAL
BR-21
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
BR
N
O
P
• Check clevis pin and plastic stopper (A) for damage and deforma-
tion. If any damage is found, replace clevis pin.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Replace the brake pedal if it has been dropped or sustained an impact.
• Check that the brake pedal height and brake pedal play meet the specifications by checking the brake pedal
and brake booster for damage and replace parts as necessary. Refer to
.
• Perform the Accelerator Pedal Released Position Learning procedure. Refer to
PFIA0756J
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст