Nissan Rogue. Manual — part 1264
FRONT WASHER NOZZLE AND TUBE
WW-59
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Removal and Installation - Front Washer Nozzle
INFOID:0000000011280417
REMOVAL
1. Remove front wiper arms (LH/RH). Refer to
WW-62, "Removal and Installation"
2. Release pawls using suitable tool (A) and remove cowl top side
trim cover (1) (LH/RH).
: Pawl
3. Disconnect front washer tube connector.
4. Release pawls and remove front washer nozzle (LH/RH).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Adjust the nozzle spray pattern. Refer to
WW-60, "Inspection and Adjustment"
.
Removal and Installation - Front Washer Tube
INFOID:0000000011280418
REMOVAL
1. Disconnect front washer tube connector.
2. Remove front over fender (RH). Refer to
EXT-30, "FRONT OVER FENDER : Removal and Installation"
.
3. Remove wind deflector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
4. Remove engine side cover (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
5. Partially remove front fender protector (RH). Refer to
EXT-28, "FENDER PROTECTOR : Exploded View"
.
6. Unclip front washer hose and remove.
1.
Cowl top cover
2.
Front washer tube
Clip
ALKIA3399ZZ
JMKIA1316ZZ
JMKIA1316ZZ
WW-60
< REMOVAL AND INSTALLATION >
FRONT WASHER NOZZLE AND TUBE
INSTALLATION
Installation is in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000011280419
WASHER TUBE INSPECTION
Check that air can pass through the check valve splitter by blowing
into the check valve splitter and that air cannot flow in the opposite
direction.
O: Air can flow
X: Air cannot flow
ADJUSTMENT
If operating properly, spray positions should match the positions shown. If spray positions do not match, con-
firm the rear washer nozzle is properly seated and working properly. If the spray positions still do not match as
shown, then replace the front washer nozzle. Refer to
WW-59, "Removal and Installation - Front Washer Noz-
JMLIA1538ZZ
1.
Windshield glass
2.
Black printed area line
3.
Front washer nozzle (LH/RH)
A.
Center line
B.
409 mm (16.10 in)
C.
103 mm (4.06 in)
D.
497 mm (19.57 in)
E.
398 mm (15.67 in)
F.
100 mm (3.94 in)
AWLIA2302ZZ
FRONT WASHER NOZZLE AND TUBE
WW-61
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
G.
356 mm (14.02 in)
H.
127 mm (5.00 in)
J.
93 mm (3.66 in)
K.
80 mm (3.15 in)
M.
133 mm (5.24 in)
N.
354 mm (13.94 in)
O.
90 mm (3.54 in)
P.
380 mm (14.96 in)
Q.
496 mm (19.53 in)
R.
103 mm (4.06 in)
S.
409 mm (16.10 in)
WW-62
< REMOVAL AND INSTALLATION >
FRONT WIPER ARM
FRONT WIPER ARM
Exploded View
INFOID:0000000011280420
Removal and Installation
INFOID:0000000011280421
REMOVAL
1. Move front wiper into the service position by turning the ignition switch ON, then quickly push the wiper
washer switch to the mist position two times within 0.5 seconds.
2. Turn the ignition switch OFF.
3. Remove front wiper arm covers.
4. Remove nuts and remove front wiper arms.
INSTALLATION
1. Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2. Move front wiper into the service position by turning the ignition switch ON, then quickly push the wiper
washer switch to the mist position two times within 0.5 seconds.
3. Turn the ignition switch OFF.
4. Adjust front wiper blade position. Refer to
5. Install front wiper arm by tightening the nuts.
6. Install front wiper arm covers.
7. Check that the front wiper blades stop at the specified position.
1.
Front wiper blade (RH)
2.
Front wiper arm (RH)
3.
Front wiper arm cover
4.
Front wiper drive assembly
5.
Front wiper arm (LH)
6.
Front wiper blade (LH)
AWLIA2294ZZ
ELH0717D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст