Nissan Qashqai J11. Manual — part 707
DIFFERENTIAL SIDE OIL SEAL
TM-403
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000010589391
Removal and Installation
INFOID:0000000010589392
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
Differential Side Oil Seal (Left Side)
1.
Remove front drive shaft (left side). Refer to
FAX-22, "Removal and Installation (LH)"
"Removal and Installation (LH)"
2.
Remove differential side oil seal
using an oil seal remover
(commercial service tool) (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
Differential Side Oil Seal (Right Side) (2WD Models Only)
1.
Remove front drive shaft (right side). Refer to
FAX-26, "Removal and Installation (RH)"
"Removal and Installation (RH)"
(4WD).
Transaxle assembly
Differential side oil seal (left side)
Differential side oil seal (right side)
(2WD models only)
: Always replace after every disassembly.
: Apply CVT fluid
JSDIA3729GB
JPDIA0118ZZ
TM-404
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
DIFFERENTIAL SIDE OIL SEAL
2.
Remove differential side oil seal
using an oil seal remover
(commercial service tool) (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse differential side oil seal.
• Apply CVT fluid to differential side oil seals.
• When inserting the drive shaft, be sure to use Tool.
Install each differential side oil seal evenly using Tool so that differ-
ential side oil seal protrudes by the dimension (C) and (D) respect-
fully.
NOTE:
The reference is the installation direction of the differential side oil seal.
Drift to be used:
Inspection and Adjustment
INFOID:0000000010589393
INSPECTION AFTER INSTALLATION
Drive the vehicle and check visually that there is no leakage of CVT fluid.
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT fluid level. Refer to
.
JPDIA0118ZZ
Tool number
: KV38107900
: Differential side oil seal (left side)
: Differential side oil seal (right side) (2WD models only)
JPDIA0520ZZ
Dimension (C)
:Height difference from case end surface is within 1.8
±
0.5 mm (0.071
±
0.020 in).
Dimension (D)
:Height difference from case end surface is within 2.2
±
0.5 mm (0.087
±
0.020 in).
Location
Commercial Service Tools
Transaxle case side
Commercial service tool with outer dia. 56 mm (2.20 in) and in-
ner dia. 50 mm (1.97 in)
Converter housing side
WATER HOSE
TM-405
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
WATER HOSE
Exploded View
INFOID:0000000010589394
Removal and Installation
INFOID:0000000010589395
REMOVAL
WARNING:
Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure
coolant escaping from the radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter turn to
allow built-up pressure to escape. Carefully remove the cap by turning it all the way.
CAUTION:
Perform when the engine is cold.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
1.
Remove air duct inlet. Refer to
2.
Remove water hose and heater thermostat assembly.
INSTALLATION
Note the followings and installation is in the reverse order of removal.
CAUTION:
• Never reuse hose clamps.
• Securely install the water hose clip to the converter housing.
Water outlet
Transaxle assembly
Heater thermostat assembly
Hose clamp
CVT oil warmer
Water hose
To thermostat housing
To engine oil cooler
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
JSDIA5317GB
TM-406
< REMOVAL AND INSTALLATION >
[CVT: RE0F10D]
WATER HOSE
• Refer to the following when installing water hoses.
• Refer to the followings when installing hose clamp.
CAUTION:
Hose clamp should not interfere with the bulge of tube.
Inspection
INFOID:0000000010589396
INSPECTION AFTER REMOVAL
Heater Thermostat
1.
Fully immerse the heater thermostat
in a container (A) filled
with water. Continue heating the water while stirring.
2.
Continue heating the heater thermostat for 5 minutes or more
after bringing the water to a boil.
3.
Quickly take the heater thermostat out of the hot water, measure the heater thermostat within 10 seconds.
Water hose
Installation side tube
Direction of paint mark
Hose insertion depth (L)
Heater thermostat assembly
CVT oil warmer
Frontward
Hose end reaches the 2-stage
bulge.
Water hose
CVT oil warmer
Frontward
Water outlet
Frontward
Hose end reaches the end of
tube.
JSDIA3579ZZ
Water hose
Installation side tube
Hose clamp
Direction of tab
Clamping position
(A)
Heater thermo-
stat assembly
CVT oil warmer
Frontward
5 – 9 mm (0.20 –
0.35 in) from hose
end
Water hose
CVT oil warmer
Upward and 30
°
frontward
5 – 7 mm (0.20 –
0.28 in) from hose
end
Water outlet
Frontward
JSDIA2424ZZ
JSDIA3661ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст