Nissan Qashqai J11. Manual — part 790
DLN-76
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
TRANSFER ASSEMBLY
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Exploded View
INFOID:0000000010755191
Removal and Installation
INFOID:0000000010755192
REMOVAL
MR20DD
1.
Remove exhaust front tube. Refer to
EX-11, "Removal and Installation"
.
2.
Remove front drive shaft (RH). Refer to
FAX-63, "Removal and Installation (RH)"
CAUTION:
Oil may leak from the opening. Use cap and/or plug to prevent leakage.
3.
Remove propeller shaft from transfer assembly. Refer to
.
CAUTION:
The joint of propeller shaft must be handled with care.
4.
Remove transfer gusset
.
5.
Remove transfer assembly from transaxle assembly.
CAUTION:
• Never damage ring gear shaft.
• Be careful when removing transfer assembly form the
vehicle because it is heavy.
INSTALLATION
Note the following, and install in the reverse order of removal.
Transfer gusset (MR20DD)
Transfer assembly
: N·m (kg-m, ft-lb)
*: Apply anti-corrosion oil.
JSDIA5353GB
JSDIA5358ZZ
TRANSFER ASSEMBLY
DLN-77
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
• When installing the transfer to the transaxle, install the mounting
bolts following the standard below, tighten bolts to the specified
torque. For each tightening torque, refer to
.
CAUTION:
• Apply anti-corrosion oil to the thread and seat of mounting bolts.
• Never damage O-ring of transfer.
• For mounting bolts of transfer gusset, temporarily tightening the engine side bolt first. After this, tighten bolts
to the specified torque in the order from transfer side bolt to engine side bolt. For tightening torque, refer to
. (MR20DD)
• Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000010755193
INSPECTION AFTER INSTALLATION
When oil leaks while removing/installing transfer assembly, check oil level after the installation. Refer to
.
Bolt symbol
Quantity
4
2
Bolt length
“L” mm (in)
40 (1.57)
40 (1.57)
Insertion direction
Transfer to transaxle
Transaxle to transfer
JSDIA5355ZZ
DLN-78
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21C]
TRANSFER COVER
UNIT DISASSEMBLY AND ASSEMBLY
TRANSFER COVER
Exploded View
INFOID:0000000010755194
MR20DD models
JSDIA5341GB
Pinion lock nut
Companion flange
Dust cover
Oil seal
Pinion bearing assembly
O-ring
Drive pinion adjusting shim
Drive pinion
O-ring
Oil seal
Dowel pin
Plug
Gasket
Transfer case
Baffle plate
Ring gear bearing adjusting shim
(transfer case side)
Ring gear bearing (transfer case
side)
Ring gear
Ring gear shaft
Ring gear shaft oil seal
Ring gear bearing (transfer cover
side)
Ring gear bearing adjusting shim
(transfer cover side)
Oil seal
O-ring
Transfer cover
Oil seal
Filler plug
Drain plug
Oil seal lip
Comply with the assembly procedure
when tightening. Refer to
.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
TRANSFER COVER
DLN-79
< UNIT DISASSEMBLY AND ASSEMBLY >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Disassembly
INFOID:0000000010755195
1.
Remove transfer cover mounting bolts (
).
2.
Lightly tap transfer cover
with a plastic hammer to remove
transfer cover.
3.
Remove O-ring from transfer cover.
CAUTION:
• Never use a suitable tool.
• Never damage transfer cover.
4.
Lightly tap the metal part of oil seals
with punch from back
side of transfer cover to remove oil seals.
CAUTION:
When removing, never damage the transfer cover by scoop-
ing it out with a suitable tool.
5.
Remove the ring gear bearing adjusting shim (transfer cover
side)
and ring gear bearing outer race (transfer cover side)
using suitable tool.
6.
Remove drain plug and gasket.
7.
Remove filler plug and gasket.
8.
Perform inspection after disassembly. Refer to
: Select with proper thickness.
: Apply transfer oil.
*
: Apply anti-corrosive oil.
: Apply multi-purpose grease.
AWDIA1139ZZ
ALDIA0446ZZ
JSDIA3990ZZ
JSDIA3992ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст