Nissan Qashqai J11. Manual — part 789
DLN-72
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
4WD CONTROL UNIT
REMOVAL AND INSTALLATION
4WD CONTROL UNIT
Exploded View
INFOID:0000000010755216
Removal and Installation
INFOID:0000000010755217
REMOVAL
1.
Turn the ignition switch OFF.
2.
Remove luggage side lower finisher LH. Refer to
3.
Disconnect 4WD control unit harness connector.
4.
Remove 4WD control unit mounting nuts
and remove 4WD
control unit
.
NOTE:
4WD control unit is located on the back side of the rear wheel
house outer panel LH.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Perform iadjustment after installation. Refer to
Adjustment
INFOID:0000000010755218
ADJUSTMENT AFTER INSTALLATION
When replaced 4WD control unit, perform writing unit characteristics. Refer to
.
4WD control unit
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA5368GB
: Vehicle front
AWDIA1154ZZ
4WD MODE SWITCH
DLN-73
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
4WD MODE SWITCH
Exploded View
INFOID:0000000010755219
Removal and Installation
INFOID:0000000010755220
REMOVAL
1.
Remove console switch panel from center console assembly. Refer to
.
2.
Disconnect 4WD mode switch harness connector.
3.
Remove 4WD mode switch from console switch panel.
INSTALLATION
Install in the reverse order of removal.
4WD mode switch
Console switch panel
JSDIA5457ZZ
DLN-74
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
TRANSFER COVER OIL SEAL
TRANSFER COVER OIL SEAL
Exploded View
INFOID:0000000010755221
MR20DD
QR25DE
NOTE:
• Replacement on vehicle may cause damage to transfer cover, and may cause a transfer oil leak.
• If transfer cover oil seal requires replacement, remove transfer assembly from the vehicle before replacing
transfer cover oil seal. Refer to
.
Removal and Installation
INFOID:0000000010755222
NOTE:
For QR25DE models only:
• Replacement on vehicle may cause damage to transfer cover, and may cause a transfer oil leak.
• If transfer cover oil seal requires replacement, remove transfer assembly from the vehicle before replacing
transfer cover oil seal. Refer to
.
REMOVAL
MR20DD
1.
Drain the transfer oil. Refer to
2.
Remove front drive shaft (right side). Refer to
.
CAUTION:
Oil may leak from the opening. Use cap and/or plug to prevent leakage.
3.
Remove transfer cover oil seal (outer/inner), using oil seal remover (commercial service tool).
CAUTION:
Never damage transfer cover.
INSTALLATION
MR20DD
Transfer assembly
Transfer cover oil seal (inner)
Transfer cover oil seal (outer)
Oil seal lip
: Always replace after every disassembly.
: Apply transfer oil.
: Apply multi-purpose grease.
JSDIA5360ZZ
TRANSFER COVER OIL SEAL
DLN-75
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21C]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
1.
Using drift (commercial service tool), install transfer cover oil
seal (outer/inner) with the directions below.
CAUTION:
• Never reuse oil seal.
• When installing, never incline oil seal.
• Apply multi-purpose grease onto oil seal lips, and transfer oil onto the circumference of oil seal.
2.
Install front drive shaft (right side). Refer to
FAX-22, "Removal and Installation (LH)"
.
3.
Refill the transfer oil to transfer assembly. Refer to
.
4.
Perform inspection after installation. Refer to
.
Inspection
INFOID:0000000010755223
INSPECTION AFTER INSTALLATION
Check oil level and transfer for oil leakage. Refer to
.
A
: Installation dimension for transfer cover oil seal (inner)
B
: Installation dimension for transfer cover oil seal (outer)
A
: 10.3 +0.6/-0 mm (0.406 +0.024/-0 in)
B
: 0 +0.6/-0 mm (0 +0.024/-0 in)
JSDIA3993ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст