Nissan Qashqai J11. Manual — part 518
EC9-228
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0335 CKP SENSOR
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CKP sensor.
CKP sensor
Resistance
+
-
Terminal
1
2
0.52 - 0.86 k
Ω
P0340 CMP SENSOR
EC9-229
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
P0340 CMP SENSOR
DTC Logic
INFOID:0000000010309155
DTC DETECTION LOGIC
NOTE:
If DTC P0340 is displayed with DTC P0016, P0335, P0560, P0641, P0651, and P0657, perform the trou-
ble diagnosis for DTC P0016, P0335, P0560, P0641, P0651, and P0657. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DIAGNOSIS PROCEDURE
NOTE:
DTC P0340 can not duplicate.
>> Proceed to
EC9-229, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010309156
1.
CHECK CMP SENSOR-1
Visually check camshaft position (CMP) sensor for chipping.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK CMP SENSOR HARNESS CONNECTOR CONNECTIONS
Check CMP sensor harness connector connection.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK CMP SENSOR CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Check CMP sensor circuit for open and short.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0340
CAMSHAFT SENSOR CIR-
CUIT
(Camshaft position sensor
“A” circuit bank 1 or single
sensor)
• 1.DEF: IMPLAUSIBLE
SIGNAL
• 2.DEF: NO SIGNAL
• Camshaft position sensor signal is not de-
tected by ECM when engine is running.
• Camshaft position sensor signal is not in the
normal pattern when engine is running.
• Harness or connectors
(The sensor circuit is open or shorted.)
• Camshaft position sensor
• Signal plate
+
-
Continuity
ECM
CMP sensor
Connector
Terminal
Connector
Terminal
F82
55
F118
1
Existed
70
2
71
3
EC9-230
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0340 CMP SENSOR
4.
CHECK CMP SENSOR-2
EC9-230, "Component Inspection (Camshaft Position Sensor)"
.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace error-detected parts.
Component Inspection (Camshaft Position Sensor)
INFOID:0000000010309157
1.
CHECK CAMSHAFT POSITION (CMP) SENSOR
1.
Disconnect CMP sensor harness connector.
2.
Check the resistance between CMP sensor terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace CMP sensor.
CMP sensor
Resistance
+
-
Terminal
1
2
More than 100 k
Ω
P0380 GLOW CONTROL SYSTEM
EC9-231
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
P0380 GLOW CONTROL SYSTEM
DTC Logic
INFOID:0000000010309158
DTC DETECTION LOGIC
NOTE:
If DTC P0380 is displayed with DTC P0560 and P0657, perform the trouble diagnosis for DTC P0560
and P0657. Refer to
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 4 minutes before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 2 seconds.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC9-231, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010309159
1.
CHECK GLOW CONTROL UNIT POWER SUPPLY CIRCUIT
1.
Turn ignition switch ON.
2.
Check the power supply of the glow control unit.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform trouble diagnosis for power supply circuit.
DTC No.
CONSULT screen terms
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P0380
PREHEATING UNIT
DIAG CONN
(Glow plug/heater circuit
“A”)
• 1.DEF: FAULT ALERT-
ED VIA THE CON-
TROL UNIT
• 2.DEF: OPERATION
TEMPERATURE TOO
HIGH
• CC.0: SHORT CIR-
CUIT TO EARTH
• CC.1: SHORT-CIR-
CUIT TO +12V
• CO: OPEN CIRCUIT
• ECM detects glow plug control unit er-
ror.
• ECM detects glow plug control circuit is
open for 1 second or more.
• ECM detects glow plug circuit is short
to ground for 1 second or more.
• ECM detects glow plug circuit is short
to power for 1 second or more.
• ECM detects an over temperature on
the glow plug control unit for 1 second
or more.
• Harness or connectors
(Glow plug control circuit is open or shorted.)
(Glow control unit input signal circuit is open or
shorted.)
• Glow plug
• Glow control unit
+
-
Voltage
Glow control unit
Connector
Terminal
F115
6
Ground
Battery voltage
10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст