Nissan Qashqai J11. Manual — part 519
EC9-232
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0380 GLOW CONTROL SYSTEM
2.
CHECK GLOW CONTROL UNIT CIRCUIT FOR OPEN AND SHORT-1
1.
Turn ignition switch OFF.
2.
Check the continuity between glow control unit harness connector and ECM harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK GLOW CONTROL UNIT CIRCUIT FOR OPEN AND SHORT-2
Check the continuity between glow control unit harness connector and glow plug harness connector.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK GLOW PLUG
EC9-232, "Component Inspection (Glow Plug)"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace error-detected parts.
5.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
Is the inspection result normal?
YES
>> Replace glow control unit.
NO
>> Repair or replace.
Component Inspection (Glow Plug)
INFOID:0000000010309160
1.
CHECK GLOW PLUG
1.
Disconnect glow plug harness connector.
2.
Check resistance between glow plug terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
+
-
Continuity
ECM
Glow control unit
Connector
Terminal
Connector
Terminal
F82
35
F115
11
Existed
67
9
+
-
Continuity
Glow control unit
Glow plug
Connector
Terminal
Connector
Terminal
F115
1
F125
1
Existed
2
F126
1
3
F127
1
4
F128
1
+
-
Resistance
Glow plug
Terminal
1
Ground
0.2 - 0.8
Ω
[at 20
°
C (68
°
F)]
P0380 GLOW CONTROL SYSTEM
EC9-233
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
NO
>> Replace malfunctioning glow plug.
EC9-234
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0402 EGR VOLUME CONTROL VALVE
P0402 EGR VOLUME CONTROL VALVE
DTC Logic
INFOID:0000000010309161
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine.
2.
Maintain the following conditions for at least 10 consecutive seconds. Hold the steady as possible.
3.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC9-234, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010309162
1.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE
Visually check high pressure EGR volume control valve for chipping.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace error-detected parts.
2.
CHECK ECM HARNESS CONNECTOR CONNECTIONS
Check ECM harness connector connection.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace error-detected parts.
3.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE HARNESS CONNECTOR CONNECTIONS
Check high pressure EGR volume control valve harness connector connection.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace error-detected parts.
4.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF.
DTC No.
CONSULT screen terms
(Trouble diagnosis con-
tent)
DTC detecting condition
Possible cause
P0402
EGR VALVE JAMMED
OPEN
(Exhaust gas recircula-
tion “A” flow excessive
detected)
• 1.DEF: MECHANICAL
FAULT
ECM detects an incorrect closed position of high
Pressure EGR volume control valve.
• Harness or connectors
• High Pressure EGR volume control
valve
ENGINE SPEED
3,500 rpm
P0402 EGR VOLUME CONTROL VALVE
EC9-235
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
2.
Check high pressure EGR volume control valve circuit for open and short.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace error-detected parts.
5.
DTC CONFIRMATION PROCEDURE
1.
Erase DTC.
2.
Perform DTC confirmation procedure again. Refer to
.
Is the DTC P0402 displayed again?
YES
>> GO TO 6.
NO
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
6.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE MOTOR
EC9-235, "Component Inspection (High Pressure EGR Volume Control Valve Motor)"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace error-detected parts.
Component Inspection (High Pressure EGR Volume Control Valve Motor)
INFOID:0000000010309163
1.
CHECK HIGH PRESSURE EGR VOLUME CONTROL VALVE MOTOR
1.
Turn ignition switch OFF.
2.
Disconnect high pressure EGR volume control valve harness connector.
3.
Check resistance between high pressure EGR volume control valve terminals as follows.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace high pressure EGR volume control valve.
+
-
Continuity
ECM
High pressure EGR volume
control valve
Connector
Terminal
Connector
Terminal
F83
144
F14
1
Existed
148
2
High pressure EGR volume
control valve
Resistance (Approx.)
+
-
Terminal
1
2
2.35
Ω
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст