Nissan Qashqai J11. Manual — part 1718
REAR COMBINATION LAMP
EXL-173
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DISASSEMBLY
Back door panel
Rear combination lamp
Grommet
: N·m (kg-m, in-lb)
JMLIA5099GB
EXL-174
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
REAR COMBINATION LAMP
Removal and Installation
INFOID:0000000010338876
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
• When removing, always use a remover tool that is made of plastic.
REMOVAL
Rear Combination Lamp (body side)
1.
Fully open trunk lid.
2.
Remove rear combination lamp mounting bolts
.
Rear combination lamp housing
(back door side)
Seal packing
Rear fog lamp bulb
(driver side only)
Rear fog lamp bulb socket
(driver side only)
Back-up lamp bulb
Back-up lamp bulb socket
Rear turn signal lamp bulb socket
Rear turn signal lamp bulb
Rear combination lamp housing
(body side)
: Vehicle front
: Always replace after every disassembly
JMLIA5407ZZ
JMLIA5137ZZ
REAR COMBINATION LAMP
EXL-175
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Pull rear combination lamp toward vehicle rear to disengage fix-
ing clips.
4.
Disconnect rear combination lamp harness connectors, and then remove rear combination lamp from
body panel.
Rear Combination Lamp (back door side)
1.
Remove back door inner finisher. Refer to
INT-31, "Removal and Installation"
2.
Remove back door finisher. Refer to
EXT-45, "Removal and Installation"
3.
Remove rear combination lamp mounting nuts
and discon-
nect rear combination lamp harness connectors.
4.
Pull rear combination lamp toward vehicle rear to remove rear combination lamp from back door.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Always replace seal packing with new part after every removal.
Replacement
INFOID:0000000010338877
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
EXL-8, "Precautions for Removing Battery Terminal"
.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned OFF.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REAR TURN SIGNAL LAMP BULB
1.
Remove rear combination lamp (body side). Refer to
EXL-174, "Removal and Installation"
2.
Rotate rear turn signal lamp bulb socket counterclockwise, and then remove rear turn signal lamp bulb
socket.
3.
Remove rear turn signal lamp bulb from rear turn signal lamp bulb socket.
STOP/TAIL LAMP
CAUTION:
Replacement of a single part is not possible due to the adoption of LED bulb. For replacement, replace
rear combination lamp assembly as a set.
REAR FOG LAMP (DRIVER SIDE ONLY)
1.
Remove rear combination lamp (back door side). Refer to
EXL-174, "Removal and Installation"
2.
Rotate rear fog lamp bulb socket counterclockwise, and then remove rear fog lamp bulb socket.
: Clip
JMLIA5138ZZ
JMLIA5139ZZ
EXL-176
< REMOVAL AND INSTALLATION >
[LED HEADLAMP]
REAR COMBINATION LAMP
3.
Remove rear fog lamp bulb from rear fog lamp bulb socket.
BACK-UP LAMP
1.
Remove rear combination lamp (back door side). Refer to
EXL-174, "Removal and Installation"
2.
Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3.
Remove back-up lamp bulb from back-up lamp bulb socket.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст