Nissan Qashqai J11. Manual — part 147
LU-48
< PERIODIC MAINTENANCE >
[R9M]
ENGINE OIL
PERIODIC MAINTENANCE
ENGINE OIL
Inspection
INFOID:0000000010284224
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check that the engine oil level. If engine is already started,
stop it and allow 10 minutes before checking.
1.
Pull out oil level gauge and wipe it clean.
2.
Insert oil level gauge and check that the engine oil level is within
the range (A) shown in the figure.
3.
If it is out of range, adjust it.
4.
When replacing engine oil this procedure must be performed.
Refer to
EC9-143, "Special Repair Requirement List"
ENGINE OIL APPEARANCE
• Check that engine oil for white turbidity or heavy contamination.
• If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following area.
• Oil pan (upper and lower)
• Oil pan drain plug
• Oil pressure switch
• Oil level sensor
• Oil filter body
• Oil cooler
• Fuel pump
• Vacuum pump
• Turbocharger
• Crankshaft position sensor
• Camshaft position sensor
• Front cover
• Mating surface between cylinder head and cylinder head housing
• Mating surface between cylinder block and cylinder head
• Mating surface between cylinder head housing and oil separator
• Front oil seal
• Rear oil seal retainer
OIL PRESSURE CHECK
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• When checking engine oil pressure, shift position should be “Neutral”, and apply parking brake
securely.
1.
Check engine oil level.
2.
Disconnect harness connector at oil pressure switch, and remove oil pressure switch using a deep socket.
CAUTION:
Handle oil pressure switch carefully and avoid impacts.
3.
Install oil pressure gauge set [SST:KV113E0020 (Mot.836-05)].
4.
Start engine and warm it up to normal operating temperature.
JPBIA0756ZZ
ENGINE OIL
LU-49
< PERIODIC MAINTENANCE >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
5.
Check oil pressure with engine running under no-load.
NOTE:
When engine oil temperature is low, engine oil pressure becomes high.
If difference is extreme, check oil passage and oil pump for oil leakage.
6.
After the inspections, install oil pressure switch with the following procedure:
a.
Tighten oil pressure switch to specification.
b.
Check engine oil level.
c.
After warming up engine, check that there is no leakage of engine oil with running engine.
Draining
INFOID:0000000010284225
WARNING:
• Be careful not to get burned, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
2.
Stop the engine and wait for 10 minutes.
3.
Remove engine undercover.
4.
Loosen oil level gauge.
5.
Remove oil pan drain plug (1) using a square driver [8 mm
(0.315 in)]. Drain engine oil.
Refilling
INFOID:0000000010284226
1.
Install drain plug with new washer.
CAUTION:
Be sure to clean drain plug and install with new washer.
2.
Refill with new engine oil.
Engine oil specification and viscosity: Refer to
MA-59, "Fluids and Lubricants"
.
CAUTION:
• The refill capacity depends on the engine oil temperature and drain time. Use these specifica-
tions for reference only.
• Always use oil level gauge to determine the proper amount of engine oil in the engine.
3.
Warm up engine and check area around drain plug and oil filter body for engine oil leakage.
4.
Stop engine and wait for 10 minutes.
5.
Check the engine oil level. Refer to
Engine oil pressure
: Refer to
Tightening torque
: Refer to
: Vehicle front
E1BIA0601ZZ
Tightening torque
: 50 N·m (5.1 Kg-m, 37 ft-lb)
Engine oil capacity
: Refer to
OIL FILTER
LU-51
< PERIODIC MAINTENANCE >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL FILTER
Removal and Installation
INFOID:0000000010284227
REMOVAL
WARNING:
Be careful not to get burned when engine and engine oil may be hot.
CAUTION:
• When removing, prepare a shop cloth to absorb any engine oil leakage or spillage.
• Completely wipe off any engine oil that adheres to engine and vehicle.
1.
Remove engine undercover.
2.
Loosen oil filter body (1) using a socket [27 mm (1.06 in)].
• Loosen oil filter body until orifice (A) of the oil filter body is
exposed, and then drain engine oil.
• Catch the engine oil drip, using a tray or waste.
CAUTION:
Completely wipe clean any engine oil remaining on oil fil-
ter body or vehicle.
3.
Remove oil filter body (3), and then remove oil filter (1) and O-
ring (2).
• Push the O-ring in the one direction by hand, and then pick a
pushed out-part with fingers to remove the O-ring.
CAUTION:
Never use wires or screwdrivers to prevent the oil filter
body from damage.
INSTALLATION
1.
Completely remove all foreign objects adhering to the inside of oil filter body or O-ring mounting area.
E1BIA0602ZZ
A
: Oil cooler side
E1BIA0600ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст