Nissan Qashqai J11. Manual — part 148
LU-52
< PERIODIC MAINTENANCE >
[R9M]
OIL FILTER
2.
Install oil filter (1) and O-ring (2) to oil filter body (3).
CAUTION:
Be sure to use a new O-ring.
• Securely press the oil filter into the oil filter body.
• When installing an O-ring, apply engine oil all around the O-
ring.
3.
Install oil filter body assembly to oil cooler.
Inspection
INFOID:0000000010284228
INSPECTION AFTER INSTALLATION
1.
Check that the engine oil level. Refer to
2.
Start the engine, and check that there is no leak of engine oil.
3.
Stop the engine and wait for 10 minutes.
4.
Check that the engine oil level, and adjust the level. Refer to
A
: Oil cooler side
E1BIA0600ZZ
Oil filter body:
25Nm (2.6 kg-m, 18 ft-lb)
OIL COOLER
LU-53
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
REMOVAL AND INSTALLATION
OIL COOLER
Exploded View
INFOID:0000000010284229
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010284230
REMOVAL
WARNING:
Be careful not to get burn yourself, as engine oil and engine coolant may be hot.
1.
Drain engine coolant from radiator. Refer to
CAUTION:
Perform this step when the engine is cold.
2.
Disconnect water hose from oil cooler.
CAUTION:
Never adhere the engine coolant to electronic equipments. (alternator etc.)
3.
Remove oil pressure switch, if necessary.
CAUTION:
Handle oil pressure switch carefully and avoid impacts.
4.
Remove oil cooler.
1.
Oil cooler bolt
2.
Oil cooler
3.
Gasket
4.
Cylinder block
5.
oil pressure sensor
6.
Oil filter body
7.
O-ring
8.
Oil filter
A.
E1BIA0598GB
LU-54
< REMOVAL AND INSTALLATION >
[R9M]
OIL COOLER
• Loosen mounting bolts in reverse order as shown in the figure.
INSTALLATION
Note the following, and install in the reverse order of removal.
Oil Cooler
• Tighten mounting bolts in the following steps in numerical order as
shown in the figure.
1.
Tighten mounting bolts No.1 and 6.
2.
Tighten all mounting bolts.
Inspection
INFOID:0000000010284231
INSPECTION AFTER REMOVAL
Oil Cooler
Check that oil cooler for cracks. Check that oil cooler for clogging by blowing through engine coolant inlet. If
necessary, replace oil cooler.
INSPECTION AFTER INSTALLATION
1.
Check that the engine oil level and the engine coolant level and add engine oil and engine coolant. Refer
to
2.
Start the engine, and check that there is no leakage of engine oil or engine coolant.
3.
Stop the engine and wait for 10 minutes.
4.
Check that the engine oil level and the engine coolant level again. Refer to
E1BIA0599ZZ
: 10 N·m (1 kg-m, 7 ft-lb)
: 10 N·m (1 kg-m, 7 ft-lb)
E1BIA0599ZZ
OIL PUMP
LU-55
< REMOVAL AND INSTALLATION >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
OIL PUMP
Exploded View
INFOID:0000000010831739
for symbol marks in the figure.
Removal and Installation
INFOID:0000000010833147
REMOVAL
1.
Remove oil pan (lower). Refer to
EM-396, "Removal and Installation"
2.
Remove oil strainer with the following procedure:
• Remove oil strainer mounting bolt (A).
• Remove oil strainer
3.
Remove oil pump with the following procedure:
• Remove oil pump bolts (B).
• Disengage oil pump with sprocket assembly from oil pump
drive chain.
• Remove oil pump.
1.
Oil strainer
2.
Oil strainer gasket
3.
Cylinder block
4.
Oil pump
5.
Oil pump sprocket
6.
Crankshaft
7.
Oil pump drive chain
8.
Crankshaft sprocket (oil pump drive
chain)
A.
E1BIA1218GB
E1BIA0659ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст