Nissan Qashqai J11. Manual — part 1526
ANTI-PINCH INSPECTION
RF-15
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
ANTI-PINCH INSPECTION
Description
INFOID:0000000010286634
Check anti-pinch function when the initialization of sunshade system is performed. Refer to
Work Procedure
INFOID:0000000010286635
1.
CHECK ANTI-PINCH FUNCTION
1.
Fully open the sunshade.
2.
Place a piece of wood near fully closed position.
3.
Close the sunshade completely with auto-slide close.
4.
Check that sunshade opens fully and stops.
CAUTION:
• Perform initialization procedure setting when auto-slide operation or anti-pinch function does not
operate normally.
• Check that auto-slide operates before inspection when system initialization is performed.
• Do not check with hands and other part of body because they may be pinched. Do not get pinched.
• Depending on environment and driving conditions, if a similar impact or load is applied to the sun-
shade it may open.
• Thermal cut out may occur if open/close operation is performed continuously. In this situation allow
system to cool before re-use.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform initialization procedure. Refer to
RF-16
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
SUNSHADE MOTOR ASSEMBLY
SUNSHADE MOTOR ASSEMBLY : Diagnosis Procedure
INFOID:0000000010286636
1.
CHECK FUSE AND FUSIBLE LINK
1.
Turn ignition switch OFF.
2.
Check that any of the following fuse and fusible link is fusing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the applicable circuit. And then replace the fuse or fusible link.
2.
CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY 1
1.
Disconnect sunshade motor assembly connector.
2.
Check voltage between sunshade motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY 2
1.
Turn ignition switch ON.
2.
Check voltage between sunshade motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
4.
CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY CIRCUIT 1
1.
Disconnect circuit breaker connector.
2.
Check voltage between circuit breaker harness connector and ground.
Is the inspection result normal?
Fuse No.
Signal name
14 (10A)
Ignition (ACC or ON) power supply
Fusible link No.
Signal name
M (50A)
Battery power supply
(+)
(
−
)
Voltage
Sunshade motor assembly
Connector
Terminal
R11
7
Ground
9 - 16 V
(+)
(
−
)
Voltage
Sunshade motor assembly
Connector
Terminal
R11
10
Ground
9 - 16 V
(+)
(
−
)
Voltage
Circuit breaker
Connector
Terminal
M86
1
Ground
9 - 16 V
POWER SUPPLY AND GROUND CIRCUIT
RF-17
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
RF
N
O
P
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK SUNSHADE MOTOR ASSEMBLY POWER SUPPLY CIRCUIT 2
Check continuity between circuit breaker harness connector and sunshade motor assembly harness connec-
tor.
Is the inspection result normal?
YES
>> Replace circuit breaker.
NO
>> Repair or replace harness.
6.
CHECK SUNSHADE MOTOR ASSEMBLY GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between sunshade motor assembly harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness.
Circuit breaker
Sunshade motor assembly
Continuity
Connector
Terminal
Connector
Terminal
M86
2
R11
7
Existed
Sunshade motor assembly
Ground
Continuity
Connector
Terminal
R11
1
Existed
RF-18
< DTC/CIRCUIT DIAGNOSIS >
SUNSHADE SWITCH
SUNSHADE SWITCH
Component Function Check
INFOID:0000000010286639
1.
CHECK FUNCTION
Check sunshade open and close operations with sunshade switch.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000010286640
1.
CHECK SUNSHADE SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect sunshade switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between sunshade switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK SUNSHADE SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect sunshade motor assembly connector.
3.
Check continuity between sunshade switch harness connector and sunshade motor assembly harness
connector.
4.
Check continuity between sunshade switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace sunshade motor assembly. Refer to
RF-30, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK SUNSHADE SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between sunshade switch harness connector and ground.
(+)
(
−
)
Voltage
Sunshade switch
Connector
Terminal
R16
1
Ground
9 - 16 V
3
Sunshade switch
Sunshade motor assembly
Continuity
Connector
Terminal
Connector
Terminal
R16
1
R11
8
Existed
3
6
Sunshade switch
Ground
Continuity
Connector
Terminal
R16
1
Not existed
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст