Nissan Qashqai J11. Manual — part 863
REAR SUSPENSION MEMBER
RSU-17
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
REAR SUSPENSION MEMBER
Exploded View
INFOID:0000000010297275
FOR 2WD GOM AND 4WD
Removal and Installation
INFOID:0000000010297276
REMOVAL
1.
Remove tires from vehicle.
2.
Remove main muffler. Refer to
(K9K),
(R9M),
(HRA2DDT) and
(MR16DDT).
3.
Remove coil spring. Refer to
4.
Remove lower link. Refer to
.
5.
Remove upper link. Refer to
.
6.
Remove rear stabilizer bar. Refer to
.
7.
Remove rear drive shaft. Refer to
8.
Remove rear propeller shaft (4WD). Refer to
.
9.
Remove rear final drive (4WD). Refer to
.
10. Remove shock absorber. Refer to
11. Set suitable jack under rear suspension member.
12. Remove mounting nuts and bolts from rear suspension member.
13. Slowly lower jack, then remove rear suspension member, lower link and upper link from vehicle as a unit.
CAUTION:
Secure suspension assembly to a suitable jack while removing it.
E1EIA0124GB
1.
Rear suspension member
2.
Suspension member stay (RH)
3.
Suspension member stay (LH)
4.
Bound bumper
: Front
Refer to
for symbols in the figure.
RSU-18
< REMOVAL AND INSTALLATION >
REAR SUSPENSION MEMBER
14. Perform the inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of the removal.
• When installing suspension member stay, face each arrow on the part toward the inside of the vehicle.
• Align the matching marks made during removal when reusing the disc brake rotor.
• Perform the final tightening of each parts removed when removing rear suspension assembly under unladen
conditions.
• Check wheel sensor harness for proper connection.
• Perform the inspection after installation. Refer to
Inspection
INFOID:0000000010297277
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Adjust parking brake operation. Refer to
.
2.
Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
3.
Adjust neutral position of steering angle sensor. Refer to
.
REAR SUSPENSION ASSEMBLY
RSU-19
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
UNIT REMOVAL AND INSTALLATION
REAR SUSPENSION ASSEMBLY
Exploded View
INFOID:0000000010297278
Removal and Installation
INFOID:0000000010297279
REMOVAL
Refer to procedure from 1 to 14 in
RSU-17, "Removal and Installation"
1.
Rear suspension member
2.
Suspension member stay (right side) 3.
Suspension member stay (left side)
4.
Stabilizer bar
5.
Stabilizer bushing
6.
Stabilizer clamp
7.
Stabilizer link
8.
Suspension bar
9.
Suspension arm bracket
10. Arm stopper
11. Suspension arm
12. Low rubber seat
13. Coil spring
14. Upper rubber seat
15. lower link
16. Upper link
17. Bound bumper
18. Shock absorber
19. Cam bolt
20. Cam washer
: Front
Refer to
for symbols in the figure.
E1EIA0125GB
RSU-20
< UNIT REMOVAL AND INSTALLATION >
REAR SUSPENSION ASSEMBLY
INSTALLATION
Note the following, and install in the reverse order of the removal.
• Perform the final tightening of each parts removed when removing rear suspension assembly under unladen
conditions.
• Check wheel sensor harness for proper connection. Refer to
.
Inspection
INFOID:0000000010297280
INSPECTION AFTER REMOVAL
Check rear suspension member for deformation, cracks, or any other damage. Replace it if necessary.
INSPECTION AFTER INSTALLATION
1.
Adjust parking brake operation. Refer to
.
2.
Check wheel alignment. Refer to
RSU-5, "Wheel Alignment Inspection"
3.
Adjust neutral position of steering angle sensor. Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст