Nissan Qashqai J11. Manual — part 1776
MAP LAMP
INL-69
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens
.
CAUTION:
Apply protect tape on remover tool.
2.
Disengage map lamp housing fixing pawl using a remover tool
(A), and then pull out lamp housing
according to numerical
order 1
→
2 indicated by arrows as shown in the figure.
CAUTION:
Apply protect tape on remover tool.
3.
Disconnect map lamp harness connector, and then remove map lamp housing.
INSTALLATION
Install in the reverse order of removal.
MAP LAMP : Replacement
INFOID:0000000010430924
MAP LAMP BULB
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse when performing the operation
for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens
.
CAUTION:
Apply protect tape on remover tool.
2.
Remove bulb.
MAP LAMP FINISHER
MAP LAMP FINISHER : Removal and Installation
INFOID:0000000010451298
CAUTION:
Disconnect the battery negative terminal or remove power circuit fuse while performing the operation
to electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
.
REMOVAL
: Pawl
JMLIA1063ZZ
: Pawl
JMLIA1064ZZ
: Pawl
JMLIA1063ZZ
INL-70
< REMOVAL AND INSTALLATION >
MAP LAMP
1.
Disengage map lamp assembly fixing pawls and metal clips
according to numerical order 1
→
3 indicated by arrows as shown
in the figure.
2.
Disconnect harness connectors, and then remove map lamp assenbly.
3.
Remove the following parts after removing map lamp assembly.
• Map lamp: Refer to
INL-68, "MAP LAMP : Removal and Installation"
• Sunshade switch: Refer to
RF-35, "Removal and Installation"
. (With sunroof)
INSTALLATION
Install in the reverse order of removal.
MAP LAMP BRACKET
MAP LAMP BRACKET : Removal and Installation
INFOID:0000000010430925
REMOVAL
1.
Remove headlining assembly. Refer to
INT-25, "Removal and Installation"
2.
Remove map lamp bracket mounting bolts
, and then remove
map lamp bracket.
INSTALLATION
Install in the reverse order of removal.
: Pawl
: Metal clip
JMLIA5190ZZ
JMLIA5191ZZ
VANITY MIRROR LAMP
INL-71
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
VANITY MIRROR LAMP
Exploded View
INFOID:0000000010430926
Replacement
INFOID:0000000010430927
VANITY MIRROR LAMP BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
1.
Apply protective tape to vanity mirror of surface for protecting it from damage.
2.
Disengage lens fixing pawls using a remover tool, and then remove lens.
CAUTION:
Use a remover tool wrapped in tape.
3.
Remove bulb.
Lens
Bulb
Lens
: Pawl
JMLIA5184ZZ
INL-72
< REMOVAL AND INSTALLATION >
GLOVE BOX LAMP
GLOVE BOX LAMP
Exploded View
INFOID:0000000010430928
LHD models
Replacement
INFOID:0000000010430929
GLOVE BOX LAMP BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it for pre-
venting damage to the bulb.
• The surface of the bulb is very hot just after the lamp is turned OFF. Never touch the glass surface of
the bulb with bare hands for preventing burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (due to dirt or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
1.
Remove instrument lower panel LH (RHD models) or RH (LHD models). Refer to
.
2.
Remove bulb & socket assembly according to numerical order
1
→
2 indicated by arrows as shown in the figure.
JMLIA5185ZZ
Lamp housing
Bulb & socket assembly
Instrument lower panel RH
: Pawl
: Vehicle front
JMLIA3624ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст