Nissan Qashqai J11. Manual — part 1777
SPICY ILLUMINATION
INL-73
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
SPICY ILLUMINATION
Exploded View
INFOID:0000000010430930
REMOVAL
LHD models
DISASSEMBLY
JMLIA5186ZZ
Console panel assembly LH
Console panel assembly RH
: Pawl
: Metal clip
JMLIA5187ZZ
INL-74
< REMOVAL AND INSTALLATION >
SPICY ILLUMINATION
Replacement
INFOID:0000000010430932
SPICY ILLUMINATION BULB
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse when performing the opera-
tion for preventing electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
• Replacement of a single part is not possible due to the adoption of LED. For replacement, replace
spicy illumination assembly.
1.
Remove console panel assembly. Refer to
IP-19, "Removal and Installation"
.
2.
Remove console panel mask lid fixing screws
, and then
remove console panel mask lid.
3.
Remove harness connector fixing clip
, and then remove spicy
illumination assembly.
Console panel bracket RH
Console panel mask lid RH
Spicy illumination assembly
Console panel RH
: Clip
: Pawl
: Metal clip
: Vehicle front
JMLIA5192ZZ
JMLIA5193ZZ
ROOM LAMP
INL-75
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
ROOM LAMP
Exploded View
INFOID:0000000010451272
Removal and Installation
INFOID:0000000010451273
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion to electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Never touch the glass surface of the bulb with bare hands because the surface is very hot just after
the lamp is turned OFF to prevent a burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (causing dirty or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
REMOVAL
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens
.
CAUTION:
Apply protect tape on remover tool.
Lamp housing
Bulb
Lens
: Pawl
: Vehicle front
JMLIA2093ZZ
: Pawl
JMLIA1230ZZ
INL-76
< REMOVAL AND INSTALLATION >
ROOM LAMP
2.
Disengage lamp housing fixing pawl using a remover tool (A),
and then pull out lamp housing
according to numerical order
1
→
2 indicated by arrows as shown in the figure.
CAUTION:
Apply protect tape on remover tool.
3.
Disconnect harness connector, and then remove lamp housing.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000010451274
CAUTION:
• Disconnect the battery negative terminal or remove power circuit fuse while performing the opera-
tion to electric leakage. Refer to
INL-3, "Precautions for Removing Battery Terminal"
.
• Never touch the glass surface of the bulb with bare hands or allow oil or grease to get on it to pre-
vent damage to the bulb.
• Never touch the glass surface of the bulb with bare hands because the surface is very hot just after
the lamp is turned OFF to prevent a burns.
• Leaving the bulb removed from housing for a long period of time can deteriorate performance of the
lens and reflector (causing dirty or clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
ROOM LAMP BULB
1.
Disengage lens fixing pawls using a remover tool (A), and then
remove lens
.
CAUTION:
Apply protect tape on remover tool.
2.
Remove bulb.
: Pawl
JMLIA1231ZZ
: Pawl
JMLIA1230ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст