Nissan Qashqai J11. Manual — part 1745
EXL-282
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
DAYTIME RUNNING LIGHT CIRCUIT
DAYTIME RUNNING LIGHT CIRCUIT
Component Function Check
INFOID:0000000010469982
1.
CHECK DAYTIME RUNNING LIGHT OPERATION
With CONSULT
1.
Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.
2.
With operating the test items, check that the daytime running light is turned ON.
Is the inspection result normal?
YES
>> Daytime running light circuit is normal.
NO
>> Refer to
EXL-282, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010469983
1.
CHECK DAYTIME RUNNING LIGHT OUTPUT VOLTAGE
With CONSULT
1.
Turn ignition switch OFF.
2.
Disconnect front combination lamp connector.
3.
Turn ignition switch ON.
4.
Select “DAYTIME RUNNING LIGHT” in “Active Test” mode of “IPDM E/R” using CONSULT.
5.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace IPDM E/R. Refer to
PCS-67, "Removal and Installation"
2.
CHECK DAYTIME RUNNING LIGHT POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DAYTIME RUNNING LIGHT GROUND CIRCUIT
Check continuity between front combination lamp harness connector and ground.
On
: Daytime running light ON
Off
: Daytime running light OFF
+
-
Test item
Voltage
IPDM E/R
Connector
Terminal
RH
E101
50
Ground
DAYTIME RUN-
NING LIGHT
On
9 – 16 V
Off
0 – 1 V
LH
E102
57
On
9 – 16 V
Off
0 – 1 V
IPDM E/R
Front combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E101
50
E92
2
Existed
LH
E102
57
E90
DAYTIME RUNNING LIGHT CIRCUIT
EXL-283
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> Replace the corresponding front combination lamp. Refer to
EXL-318, "Removal and Installation"
.
NO
>> Repair or replace harness.
Front combination lamp
—
Continuity
Connector
Terminal
RH
E92
1
Ground
Existed
LH
E90
EXL-284
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
STOP LAMP CIRCUIT
STOP LAMP CIRCUIT
Component Function Check
INFOID:0000000010469984
1.
CHECK STOP LAMP OPERATION
1.
Turn ignition switch ON.
2.
With operating the brake pedal, check that the stop lamp and high-mounted stop lamp is turned ON.
Is the inspection result normal?
YES
>> Stop lamp circuit is normal.
NO
>> Refer to
EXL-284, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000010469985
1.
CHECK SYMPTOM
Check symptom (A or B)
Which symptom is detected?
A
>> GO TO 2.
B
>> GO TO 7.
2.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
3.
CHECK BCM POWER SUPPLY (STOP LAMP)
1.
Disconnect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK STOP LAMP SWITCH POWER SUPPLY
1.
Disconnect stop lamp switch connector.
Depressed
: Stop lamp and high-mounted stop lamp
ON
Fully re-
leased
: Stop lamp and high-mounted stop lamp
OFF
Symptom
A
All of stop lamp and high-mounted stop lamp are not turned ON
B
Any of stop lamp and high-mounted stop lamp are not turned ON
Unit
Location
Fuse No.
Capacity
• BCM
• Stop lamp switch
Fuse block (J/B)
#24
10 A
+
-
Voltage
BCM
Connector
Terminal
M68
145
Ground
9 – 16 V
STOP LAMP CIRCUIT
EXL-285
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2.
Connect BCM connector.
3.
Turn ignition switch ON.
4.
Check voltage between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK STOP LAMP SWITCH SIGNAL CIRCUIT (OPEN)
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and stop lamp switch harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK STOP LAMP SWITCH
Check stop lamp switch. Refer to
EXL-287, "Component Inspection"
.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Replace stop lamp switch. Refer to
(LHD models) or
(RHD models).
7.
CHECK STOP LAMP / HIGH-MOUNTED STOP LAMP OUTPUT VOLTAGE
With CONSULT
1.
Disconnect stop lamp / tail lamp (body side) connectors.
2.
Turn ignition switch ON.
3.
Select “HEAD LAMP” of “BCM” using CONSULT.
4.
Select “STOP LAMP 1”, “STOP LAMP 2” or “STOP LAMP 3” in “Active Test” mode.
5.
With operating the test items, check voltage between BCM harness connector and ground.
Stop lamp RH
Stop lamp LH
+
-
Voltage
Stop lamp switch
Connector
Terminal
M97
1
Ground
9 – 16 V
BCM
Stop lamp switch
Continuity
Connector
Terminal
Connector
Terminal
E60
157
E50
2
Existed
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
B3
134
Ground
STOP LAMP 1
On
9 – 16 V
Off
0 V
+
-
Test item
Voltage
(Approx.)
BCM
Connector
Terminal
B3
129
Ground
STOP LAMP 2
On
9 – 16 V
Off
0 V
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст