Nissan Qashqai J11. Manual — part 524
EC9-252
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0560 BATTERY VOLTAGE
P0560 BATTERY VOLTAGE
DTC Logic
INFOID:0000000010309197
DTC DETECTION LOGIC
NOTE:
If this DTC is detected, first confirm self-diagnostic result in IPDM E/R.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 10 seconds.
2.
Check DTC.
Is DTC detected?
YES
>> Proceed to
EC9-252, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010309198
1.
CHECK BATTERY VOLTAGE
1.
Turn ignition switch ON.
2.
Check battery voltage.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Recharge the battery.
2.
CHECK BATTERY TERMINALS
1.
Turn ignition switch OFF.
2.
Check battery terminals condition.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the battery terminals.
3.
CHECK BATTERY AND ALTERNATOR
Check that the proper type of battery and type of alternator are installed.
Refer to,
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> Replace with a proper one.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0560
COMPUTER SUPPLY
VOLTAGE
(System voltage)
• 1.DEF: VOLTAGE TOO
LOW
• 2.DEF: VOLTAGE TOO
HIGH
• A battery power supply voltage re-
mains more than 17 V or more for
2.5 seconds or more.
• A battery power supply voltage re-
mains less than 9 V or more for 10
seconds or more.
• Harness or connectors
(ECM power supply circuit is open or shorted.)
• Battery
• Battery terminal
• Alternator
• IPDM E/R
Voltage: Above 11 V
P0564 ASCD STEERING SWITCH
EC9-253
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
P0564 ASCD STEERING SWITCH
DTC Logic
INFOID:0000000010309199
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 10 seconds.
2.
Press RESUME/ACCELERATE switch for at least 10 seconds, then release it and wait at least 10 sec-
onds.
3.
Press SET/COAST switch for at least 10 seconds, then release it and wait at least 10 seconds.
4.
Press CANCEL switch for at least 10 seconds, then release it and wait at least 10 seconds.
5.
Check DTC.
Is DTC detected?
YES
>> Go to
EC9-253, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010309200
1.
CHECK ASCD STEERING SWITCH CIRCUIT
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connector terminals as follows.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 2.
2.
CHECK ASCD STEERING SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch OFF and wait at least 1 minute.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0564
SL LMTR/CC FNC
(Cruise control multi-function
input “A” circuit)
• 1.DEF: VALUES OUTSIDE
TOLERANCES
• 2.DEF: SIGNAL INCO-
HERENCE
• CO.1: OPEN CIRCUIT OR
SHORT CIRCUIT TO +12
V
• An ASCD steering switch signal voltage is
out of the specified range.
• ASCD steering switch signal circuit is open.
• ASCD steering switch signal circuit is short
to battery.
• ECM cannot detect the ASCD steering
switch signal.
• Harness or connectors
(The switch circuit is open or shorted.)
• ASCD steering switch
ECM
Condition
Voltage
(Approx.)
Connector
+
–
Terminal
E58
15
14
CANCEL switch: Pressed
1.0 V
SET/COAST switch: Pressed
2.0 V
RESUME/ACCELERATE switch: Pressed
3.0 V
All ASCD steering switches: Released
4.0 V
EC9-254
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
P0564 ASCD STEERING SWITCH
2.
Disconnect combination switch harness connector.
3.
Disconnect ECM harness connector.
4.
Check the continuity between combination switch (spiral cable) and ECM harness connector.
5.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
3.
CHECK ASCD STEERING SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check the continuity between combination switch (spiral cable) and ECM harness connector.
2.
Also check harness for short to ground and short to power.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair open circuit, short to ground or short to power in harness or connectors.
4.
CHECK ASCD STEERING SWITCH
EC9-254, "Component Inspection (ASCD Steering Switch)"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace ASCD steering switch.
5.
CHECK INTERMITTENT INCIDENT
GI-41, "Intermittent Incident"
>> INSPECTION END
Component Inspection (ASCD Steering Switch)
INFOID:0000000010309201
1.
CHECK ASCD STEERING SWITCH
1.
Disconnect combination switch (spiral cable) harness connector.
2.
Check the continuity between combination switch harness connector terminals under following conditions.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace ASCD steering switch.
+
-
Continuity
Combination switch (spiral cable)
ECM
Connector
Terminal
Connector
Terminal
M66
28
E58
14
Existed
+
-
Continuity
Combination switch (spiral cable)
ECM
Connector
Terminal
Connector
Terminal
M66
27
E58
15
Existed
Combination switch
Condition
Resistance
(Approx.)
Connector
+
-
Terminals
M353
8
9
CANCEL switch: Pressed
250
Ω
SET/COAST switch: Pressed
660
Ω
RESUME/ACCELERATE switch: Pressed
1,480
Ω
All ASCD steering switches: Released
4,000
Ω
P0575 ASCD STEERING SWITCH
EC9-255
< DTC/CIRCUIT DIAGNOSIS >
[R9M]
C
D
E
F
G
H
I
J
K
L
M
A
EC9
N
P
O
P0575 ASCD STEERING SWITCH
DTC Logic
INFOID:0000000010309207
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at
least 1 minute before conducting the next test.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 5 seconds.
2.
Check DTC.
Is DTC detected?
YES
>> Go to
EC9-255, "Diagnosis Procedure"
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010309208
1.
CHECK ASCD STEERING SWITCH SIGNAL-1
1.
Turn ignition switch ON.
2.
Check the voltage between ECM harness connector terminals as follows.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-41, "Intermittent Incident"
.
NO
>> GO TO 2.
2.
CHECK ASCD STEERING SWITCH
1.
Turn ignition switch OFF and wait at least 1 minute.
2.
Disconnect combination switch harness connector.
3.
Check the continuity between combination switch (spiral cable) harness connector terminals.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible Cause
P0575
CC/SL LMTR BUTTONS
(Cruise control input circuit)
• 1.DEF: IMPLAUSIBLE
SIGNAL
ECM receives ASCD MAIN switch signal and
Speed Limiter MAIN switch signal simulta-
neously.
ASCD steering switch
+
–
Condition
Voltage
(Approx.)
ECM
Connector
Terminal
E58
3
Ground
• ASCD MAIN switch: NOT pressed
• Speed Limiter MAIN switch: NOT pressed
0 V
10
3
• ASCD MAIN switch: Pressed
• Speed Limiter MAIN switch: NOT pressed
Battery Voltage
10
0 V
3
• ASCD MAIN switch: NOT pressed
• Speed Limiter MAIN switch: Pressed
0 V
10
Battery Voltage
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст