Nissan Qashqai J11. Manual — part 223

ECH-190

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

P0201, P0202, P0203, P0204 FUEL INJECTOR

2.

Also check harness for short to ground and short to power.

Is the inspection result normal?

YES

>> Replace malfunctioning fuel injector.

NO

>> Repair open circuit or short to ground or short to power in harness or connectors.

Component Inspection

INFOID:0000000010788020

1.

CHECK FUEL INJECTOR

1.

Turn ignition switch OFF.

2.

Disconnect fuel injector harness connector.

3.

Check resistance between fuel injector terminals as follows.

Is the inspection result normal?

YES

>> INSPECTION END
>> Replace malfunctioning fuel injector. Refer to

EM-42, "Removal and Installation"

.

Fuel injector

ECM

Continuity

Cylinder

Connector

Terminal

Connector

Terminal

1

F167

1

F18

153

Existed

2

F168

155

3

F169

154

4

F170

156

Terminals

Resistance (

Ω

)

1 and 2

1.94

±

0.2

Ω

[at 20

°

C (68

°

F)]

2.7

Ω

[at 120

°

C (248

°

F)]

P0217 ENGINE OVER TEMPERATURE

ECH-191

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

C

D

E

F

G

H

I

J

K

L

M

A

ECH

N

P

O

P0217 ENGINE OVER TEMPERATURE

DTC Logic

INFOID:0000000010379082

DTC DETECTION LOGIC

If the cooling fan or another component in the cooling system malfunctions, engine coolant temperature will
rise.
When the engine coolant temperature reaches an abnormally high temperature condition, a malfunction is
indicated.
NOTE:
If DTC P0217 is display with DTC P0115 or P0597, first perform the trouble diagnosis for DTC P0115 or
P0597. Refer to

ECH-71, "DTC Index"

.

CAUTION:

When a malfunction is indicated, be sure to replace the coolant. Refer to

CO-11, "Draining"

and

CO-11,

"Refilling"

. Also, replace the engine oil. Refer to

LU-9, "Draining"

and

LU-9, "Refilling"

.

1.

Fill radiator with coolant up to specified level with a filling speed of 2 liters per minute. Be sure to
use coolant with the proper mixture ratio. Refer to

MA-61, "Engine Coolant Mixture Ratio"

.

2.

After refilling coolant, run engine to ensure that no water-flow noise is emitted.

DTC CONFIRMATION PROCEDURE

1.

PERFORM COMPONENT FUNCTION CHECK

Perform component function check. Refer to

ECH-191, "Component Function Check"

.

NOTE:
Use component function check to check the overall function of the cooling fan. During this check, a DTC might
not be confirmed.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Go to

ECH-192, "Diagnosis Procedure"

.

Component Function Check

INFOID:0000000010379083

1.

PERFORM COMPONENT FUNCTION CHECK-1

WARNING:

Never remove the radiator cap when the engine is hot. Serious burns could be caused by high pres-
sure fluid escaping from the radiator.
Wrap a thick cloth around cap. Carefully remove the cap by turning it a quarter turn to allow built-up
pressure to escape. Then turn the cap all the way off.

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detecting condition

Possible cause

P0217

ENG COOLANT TEMP
(Engine coolant over tem-
perature condition)

Engine coolant over temperature becomes
too high for 1 second or more.

• Harness or connectors

(The cooling fan circuit is open or shorted.)

• Cooling fan motor
• Radiator hose
• Radiator
• Radiator cap
• Water pump
• Thermostat
• Engine coolant temperature sensor

ECH-192

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

P0217 ENGINE OVER TEMPERATURE

Check the coolant level in the reservoir tank and radiator.
Allow engine to cool before checking coolant level.
Is the coolant level in the reservoir tank and/or radiator below the
proper range?

YES

>> Proceed to

ECH-192, "Diagnosis Procedure"

.

NO

>> GO TO 2

2.

PERFORM COMPONENT FUNCTION CHECK-2

Confirm whether customer filled the coolant or not.

Did customer fill the coolant?

YES

>> Proceed to

ECH-192, "Diagnosis Procedure"

.

NO

>> GO TO 3.

3.

PERFORM COMPONENT FUNCTION CHECK-3

Without CONSULT

1.

Start engine and let it idle.

2.

Turn air conditioner switch and blower fan switch ON.

3.

Make sure that cooling fan operates at low speed.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Proceed to

ECH-192, "Diagnosis Procedure"

.

4.

PERFORM COMPONENT FUNCTION CHECK-4

Without CONSULT

1.

Turn ignition switch OFF.

2.

Turn air conditioner switch and blower fan switch OFF.

3.

Disconnect engine coolant temperature sensor harness connector.

4.

Connect 150

Ω

resistor to engine coolant temperature sensor harness connector.

5.

Restart engine and make sure that cooling fan operates at higher speed than low speed.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Proceed to

ECH-192, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000010379084

1.

CHECK COOLING SYSTEM FOR LEAK-1

Check cooling system for leak.

Is leakage detected?

YES

>> GO TO 2.

NO

>> GO TO 3.

2.

CHECK COOLING SYSTEM FOR LEAK-2

Check the following for leak.
• Hose
• Radiator (Refer to

CO-19, "Inspection"

.)

• Water pump (Refer to

CO-23, "Inspection"

.)

>> Repair or replace malfunctioning part.

3.

CHECK RADIATOR CAP

Check radiator cap. Refer to

CO-15, "Inspection"

.

Is the inspection result normal?

SEF621W

P0217 ENGINE OVER TEMPERATURE

ECH-193

< DTC/CIRCUIT DIAGNOSIS >

[HRA2DDT]

C

D

E

F

G

H

I

J

K

L

M

A

ECH

N

P

O

YES

>> GO TO 4.

NO

>> Replace radiator cap.

4.

CHECK THERMOSTAT

Check thermostat. Refer to

CO-26, "Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace thermostat. Refer to

CO-25, "Removal and Installation"

.

5.

CHECK ENGINE COOLANT TEMPERATURE SENSOR

Check engine coolant temperature sensor. Refer to

ECH-282, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 6.

NO

>> Replace engine coolant temperature sensor.

6.

OVERHEATING CAUSE ANALYSIS

If the cause cannot be isolated, check

CO-9, "Troubleshooting Chart"

.

>> INSPECTION END