Nissan Qashqai J11. Manual — part 809
DLN-152
< PERIODIC MAINTENANCE >
[TRANSFER: TY30A]
TRANSFER OIL
PERIODIC MAINTENANCE
TRANSFER OIL
Inspection
INFOID:0000000010288332
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, filler plug, and transfer case, etc.) for oil leakage.
OIL LEVEL
1.
Remove filler plug (1) and gasket. Then check that oil is filled up
(A) from mounting hole for the filler plug.
2.
Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to
CAUTION:
Never reuse gaskets.
Draining
INFOID:0000000010288333
1.
Run the vehicle to warm up the transfer unit sufficiently.
2.
Stop the engine and remove drain plug (1) and gaskets to drain
the transfer oil.
CAUTION:
Never remove tooth contact test hole plug (2).
3.
Before installing drain plug, set a new gasket. Install drain plug
on transfer and tighten to the specified torque. Refer to
CAUTION:
Never reuse gaskets.
Refilling
INFOID:0000000010288334
1.
Remove filler plug (1) and gasket. Then fill oil up to mounting
hole (A) for the filler plug.
CAUTION:
Carefully fill the oil. (Fill up for approximately 3 minutes.)
2.
Leave the vehicle for 3 minutes. Then check oil level again.
3.
Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to
.
CAUTION:
Never reuse gasket.
SDIA3060J
SDIA3059J
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
SDIA3060J
AWD CONTROL UNIT
DLN-153
< REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
AWD CONTROL UNIT
Exploded View
INFOID:0000000010471495
Removal and Installation
INFOID:0000000010471496
REMOVAL
1.
Remove luggage side lower finisher (LH). Refer to
.
2.
Disconnect AWD control unit harness connector.
3.
Remove AWD control unit bolts (
).
NOTE:
AWD control unit is located on the back side of body panel.
4.
Remove AWD control unit.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not drop or shock AWD control unit.
• When replacing AWD control unit, perform writing unit characteristic. Refer to
AWD control unit
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA5368GB
: Front
AWDIA1154ZZ
DLN-154
< REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
AWD MODE SWITCH
AWD MODE SWITCH
Exploded View
INFOID:0000000010464154
Removal and Installation
INFOID:0000000010464155
REMOVAL
1.
Remove instrument lower panel LH. Refer to
2.
Disconnect AWD lock switch harness connector (A).
3.
Remove AWD lock switch from lower switch bracket (2).
INSTALLATION
Install in the reverse order of removal.
1.
Instrument lower panel LH
2.
AWD lock switch
Front
Pawl
ALDIA0506ZZ
: Pawls
AWDIA1151ZZ
TRANSFER ASSEMBLY
DLN-155
< UNIT REMOVAL AND INSTALLATION >
[TRANSFER: TY30A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
UNIT REMOVAL AND INSTALLATION
TRANSFER ASSEMBLY
Exploded View
INFOID:0000000010288345
Removal and Installation
INFOID:0000000010288346
REMOVAL
1.
Remove the exhaust front tube. Refer to
2.
Separate the rear propeller shaft. Refer to
3.
Remove right side drive shaft and support bearing bracket. Refer to
.
4.
Remove the diesel particle filter. Refer to
5.
Remove the gusset.
6.
Remove the rear torque rod. Refer to
.
1.
Gusset
2.
Transfer assembly
3.
O-ring (outer)
: Vehicle front
: Apply multi-purpose grease.
Refer to
for symbols not described on the above.
JSDIA0267GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст