Nissan Qashqai J11. Manual — part 612
PREPARATION
TM-23
< PREPARATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Drift
a: 45 mm (1.77 in) dia.
b: 39 mm (1.54 in) dia.
Installing differential side bearing inner race
(clutch housing side)
Drift
a: 52 mm (2.05 in) dia.
b: 45 mm (1.77 in) dia.
Installing differential side bearing inner race
(transaxle case side)
Tool name
Description
S-NT474
S-NT474
TM-24
< PERIODIC MAINTENANCE >
[6MT: RS6F94R]
GEAR OIL
PERIODIC MAINTENANCE
GEAR OIL
Exploded View
INFOID:0000000010288444
.
Draining
INFOID:0000000010288445
1.
Start engine and let it run to warm up transaxle.
2.
Stop engine. Remove drain plug (1) and then drain gear oil.
3.
Set a gasket on drain plug and install it to clutch housing.
Tighten drain plug to the specified torque.
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000010288446
1.
Remove filler plug (1). Fill with new gear oil until oil level reaches
the specified limit at filler plug hole as shown.
2.
After refilling gear oil, check oil level. Refer to
3.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
4.
Tighten filler plug to the specified torque.
Inspection
INFOID:0000000010288447
LEAKAGE
Make sure that gear oil is not leaking from transaxle or around it.
LEVEL
1.
Remove filler plug (1) and check oil level at filler plug hole as
shown.
CAUTION:
Never start engine while checking oil level.
2.
Set a gasket on filler plug and then install it to transaxle case.
CAUTION:
Never reuse gasket.
3.
Tighten filler plug to the specified torque.
SCIA7622E
Oil grade and viscosity
: Refer to
.
Oil capacity
: Refer to
.
SCIA7623E
SCIA7623E
M/T SHIFT SELECTOR
TM-25
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
REMOVAL AND INSTALLATION
M/T SHIFT SELECTOR
Exploded View
INFOID:0000000010735671
Removal and Installation
INFOID:0000000010735672
REMOVAL
1.
Shift shift lever to the neutral position.
2.
Pull shift lever knob
upward to remove.
3.
Remove center console assembly. Refer to
.
4.
Disconnect and remove shift cable and select cable from M/T
shift selector assembly. Refer to
5.
Remove M/T shift selector assembly
from M/T shift selector
bracket .
Shift lever knob
M/T shift selector assembly
M/T shift selector bracket
: N·m (kg-m, in-lb)
: Always replace after every disassembly.
JSDIA5662GB
JSDIA5753ZZ
JSDIA5749ZZ
TM-26
< REMOVAL AND INSTALLATION >
[6MT: RS6F94R]
M/T SHIFT SELECTOR
6.
Remove M/T shift selector bracket
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• For each tightening torque, refer to
• Install shift lever knob to the shift lever, as per the following procedure.
CAUTION:
Never reuse shift lever knob.
1.
Turn shift lever knob
counterclockwise (30 degrees) and
insert it straight to the shift lever
without pressing the orna-
ment .
2.
Protrude the ornament
of shift lever knob
.
3.
Turn shift lever knob
clockwise (30 degrees) until coming to a
stop.
JSDIA5750ZZ
: Vehicle front
JSDIA6032ZZ
: Vehicle front
JSDIA6033ZZ
: Vehicle front
JSDIA6034ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст