Nissan Qashqai J11. Manual — part 2207
DAS-242
< BASIC INSPECTION >
[CHASSIS CONTROL]
CONFIGURATION (CHASSIS CONTROL MODULE)
Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
>> GO TO 8.
8.
WRITING (MANUAL WRITING)
CONSULT Configuration
1.
Select “Manual Configuration”.
2.
Select the “Type ID” searched by using FAST (service parts catalogue) to write the “Type ID” into the
chassis control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
9.
VERIFYING TYPE ID (2)
Compare “Type ID” written into the chassis control module with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 10.
10.
CHECKING CHASSIS CONTROL WARNING
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON and check that the chassis control warning to information display of combina-
tion meter displays OFF after staying illuminated for approximately two seconds.
CAUTION:
Never start the engine.
Is the inspection result normal?
YES
>> GO TO 11.
NO
>> Perform the “Self Diagnostic Result” of “CHASSIS CONTROL”. Refer to
.
11.
PERFORMING SUPPLEMENTARY WORK
1.
Perform the self-diagnosis of all systems.
2.
Erase self-diagnosis results.
>> End of work.
DAS
C1B92-00 BRAKE CONTROL SYSTEM
DAS-243
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
DTC/CIRCUIT DIAGNOSIS
C1B92-00 BRAKE CONTROL SYSTEM
DTC Description
INFOID:0000000010416985
DTC DETECTION LOGIC
POSSIBLE CAUSE
• ABS actuator and electric unit (control unit) system
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control function
• Active Trace Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B92-00” detected?
YES
>> Proceed to
DAS-243, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416986
1.
CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
With CONSULT
Perform self-diagnosis for “ABS”.
Is DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1B92”, “U1000” or other DTC detected?
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B92-00
BRAKE CONTROL SYSTEM
(Brake control system)
When a malfunction is detected in ABS actuator and electric unit (control unit) sys-
tem.
DAS-244
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C1B92-00 BRAKE CONTROL SYSTEM
YES (“C1B92-00”)>>Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
YES (“U1000-00”)>>Refer to
DAS-286, "Diagnosis Procedure"
YES (other DTC)>>Check the DTC.
NO
>> INSPECTION END
DAS
C1B93-00 ENGINE/HEV SYSTEM
DAS-245
< DTC/CIRCUIT DIAGNOSIS >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1B93-00 ENGINE/HEV SYSTEM
DTC Description
INFOID:0000000010416987
DTC DETECTION LOGIC
POSSIBLE CAUSE
• Engine system
• ECM
• Chassis control module
FAIL-SAFE
The following functions are suspended.
• Active Ride Control (engine) function
• Active Trace Control function
• Active Engine Brake function
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.
CHECK DTC DETECTION
With CONSULT
1.
Turn the ignition switch OFF to ON.
CAUTION:
Be sure to wait of 10 seconds after turning ignition switch OFF or ON.
2.
Perform self-diagnosis for “CHASSIS CONTROL”.
Is DTC “C1B93-00” detected?
YES
>> Proceed to
DAS-245, "Diagnosis Procedure"
NO-1
>> To check malfunction symptom before repair: Refer to
GI-41, "Intermittent Incident"
NO-2
>> Confirmation after repair: INSPECTION END
Diagnosis Procedure
INFOID:0000000010416988
1.
CHECK ECM SYSTEM
With CONSULT
Perform self-diagnosis for “ENGINE”.
Is DTC detected?
YES
>> Check the DTC. Refer to
(HRA2DDT),
(K9K) or
(R9M)
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
1.
Erase self-diagnosis result for “CHASSIS CONTROL”.
2.
Turn the ignition switch OFF and wait for 10 seconds or more.
3.
Turn the ignition switch ON.
4.
Perform “All DTC Reading”.
Is DTC “C1B93-00”, “U1000-00” or other DTC detected?
DTC
Display Item
(Trouble diagnosis content)
Malfunction detected condition
C1B93-00
ENGINE/HEV SYSTEM
(Engine/HEV system)
When a malfunction is detected in ECM system.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст