Nissan Qashqai J11. Manual — part 2206
DAS-238
< BASIC INSPECTION >
[CHASSIS CONTROL]
DIAGNOSIS AND REPAIR WORK FLOW
Is the symptom reproduced?
YES
>> GO TO 3.
NO
>> Inspection End.
Diagnostic Work Sheet
INFOID:0000000010416982
Description
• In general, customers have their own criteria for a symptom. Therefore, it is important to understand the
symptom and status well enough by interviewing the customer about the symptom carefully. To systemize all
the information for the diagnosis, prepare the interview sheet referring to the interview points.
• In some cases, multiple conditions that appear simultaneously may cause a DTC to be detected.
INTERVIEW SHEET SAMPLE
Interview sheet
Customer
name
MR/MS
Registration
number
Initial year
registration
Vehicle type
VIN
Storage date
Engine, Trac-
tion motor
Mileage
km ( Mile)
Symptom
Does not operate ( ) function
Warning lamp for ( ) turns ON.
Noise
Vibration
Other
( )
First occurrence
Recently
Other ( )
Frequency of occurrence
Always
Under a certain conditions of
Sometimes ( time(s)/day)
Climate con-
ditions
Irrelevant
Weather
Fine
Cloud
Rain
Snow
Others ( )
Temperature
Hot
Warm
Cool
Cold
Temperature [Approx.
°
C (
°
F)]
Relative humidity
High
Moderate
Low
Road conditions
Urban area
Suburb area
Highway
Mountainous road (uphill or downhill)
Rough road
Operating condition, etc.
Irrelevant
When traction motor starts
During idling
During driving
During acceleration
At constant speed driving
During deceleration
During cornering (right curve or left curve)
When steering wheel is steered (to right or to left)
Other conditions
DAS
DIAGNOSIS AND REPAIR WORK FLOW
DAS-239
< BASIC INSPECTION >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
Vehicle equipment
Memo
Interview sheet
Customer
name
MR/MS
Registration
number
Initial year
registration
Vehicle type
VIN
Storage date
Engine, Trac-
tion motor
Mileage
km ( Mile)
DAS-240
< BASIC INSPECTION >
[CHASSIS CONTROL]
ADDITIONAL SERVICE WHEN REPLACING CHASSIS CONTROL MODULE
ADDITIONAL SERVICE WHEN REPLACING CHASSIS CONTROL MOD-
ULE
Description
INFOID:0000000010416983
When replaced the chassis control module, configuration of the chassis control module is required. Refer to
DAS
CONFIGURATION (CHASSIS CONTROL MODULE)
DAS-241
< BASIC INSPECTION >
[CHASSIS CONTROL]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
CONFIGURATION (CHASSIS CONTROL MODULE)
Work Procedure
INFOID:0000000010416984
CAUTION:
• Use “Manual Configuration” only when “TYPE ID” of the chassis control module cannot be read.
• After configuration, turn the ignition switch from OFF to ON and check that the chassis control warn-
ing to information display of combination meter displays OFF after staying illuminated for approxi-
mately two seconds.
• If an error occurs during configuration, start over from the beginning.
1.
CHECKING TYPE ID (1)
Use FAST (service parts catalogue) to search the chassis control module of the applicable vehicle and find
“Type ID”.
Is “Type ID” displayed?
YES
>> Print out “Type ID” and GO TO 2.
NO
>> “Configuration” is not required for the chassis control module. Replace in the usual manner. Refer
to
DAS-312, "Removal and Installation"
2.
CHECKING TYPE ID (2)
CONSULT Configuration
1.
Select “Before Replace ECU” of “Read/Write Configuration”.
2.
Check that “Type ID” is displayed on the CONSULT screen.
Is “Type ID” displayed?
YES
>> GO TO 3.
NO
>> GO TO 7.
3.
VERIFYING TYPE ID (1)
CONSULT Configuration
Compare a “Type ID” displayed on the CONSULT screen with the one searched by using FAST (service parts
catalogue) to check that these “Type ID” agree with each other.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 4.
4.
SAVING TYPE ID
CONSULT Configuration
Save “Type ID” on CONSULT.
>> GO TO 5.
5.
REPLACING CHASSIS CONTROL MODULE (1)
Replace the chassis control module. Refer to
DAS-312, "Removal and Installation"
.
>> GO TO 6.
6.
WRITING (AUTOMATIC WRITING)
CONSULT Configuration
1.
Select “After Replace ECU” of “Re/programming, Configuration” or that of “Read / Write Configuration”.
2.
Select the “Type ID” agreeing with the one stored on CONSULT and the one searched by using FAST
(service parts catalogue) to write the “Type ID” into the chassis control module.
NOTE:
For the “Type ID” searched by using FAST (service parts catalog), use the last five digits of the “Type ID”.
>> GO TO 9.
7.
REPLACING CHASSIS CONTROL MODULE (2)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст