Nissan Qashqai J11. Manual — part 2035
MWI-76
< DTC/CIRCUIT DIAGNOSIS >
METER CONTROL SWITCH SIGNAL CIRCUIT
Component Inspection
INFOID:0000000010435887
1.
CHECK METER CONTROL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect meter control switch connector.
3.
Check meter control switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace meter control switch. Refer to
MWI-87, "Removal and Installation"
.
Meter control switch
Condition
Continuity
Terminals
7
4
When illumination control switch (
−
) is pressed
Yes
Other than the above
No
5
When trip reset switch is pressed
Yes
Other than the above
No
6
When illumination control switch (+) is pressed
Yes
Other than the above
No
MWI
STEERING SWITCH
MWI-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING SWITCH
Description
INFOID:0000000010435888
When one of the steering switches is pushed, the resistance in the steering switch changes the signal to
identify which button is controlling the information display.
Diagnosis Procedure
INFOID:0000000010435889
Regarding Wiring Diagram information, refer to
.
1.
CHECK STEERING SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter harness connector M51 and spiral cable harness connector M303.
3.
Check continuity between combination meter harness connector M51 and spiral cable harness connector
M303.
4.
Check continuity between combination meter harness connector M51 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connector.
Component Inspection
INFOID:0000000010435890
1.
CHECK STEERING SWITCH RESISTANCE
Check resistance between the following steering switch terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace steering wheel switch. Refer to
Combination meter
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M51
21
M303
4
Yes
22
5
23
10
Combination meter
Ground
Continuity
Connector
Terminal
M51
21
No
22
23
Terminal
Signal name
Condition
Resistance (
Ω
)
(Approx.)
10
4
Display
Depress DISP switch.
2023
Back
Depress
switch.
723
5
Enter
Depress ENTER switch.
2023
Menu Up
Depress
switch.
121
Menu Down
Depress
switch.
321
MWI-78
< DTC/CIRCUIT DIAGNOSIS >
STEERING SWITCH
2.
CHECK SPIRAL CABLE
Check continuity between the following spiral cable terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace spiral cable. Refer to
SR-17, "Removal and Installation"
Terminals
Continuity
24
10
Yes
29
5
23
4
MWI
THE FUEL GAUGE DOES NOT MOVE
MWI-79
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
THE FUEL GAUGE DOES NOT MOVE
Description
INFOID:0000000010329995
Fuel gauge does not move from a certain position.
Diagnosis Procedure
INFOID:0000000010329996
1.
CONDUCTING THE COMBINATION METER SELF-DIAGNOSIS MODE
Perform the self-diagnosis mode of combination meter, and then check that the fuel gauge operates normally.
Refer to
MWI-30, "CONSULT Function (METER/M&A)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace combination meter. Refer to
MWI-86, "Removal and Installation"
2.
CHECK FLOAT INTERFERENCE
Check that the float arm interferes with or binds to other components in the fuel tank.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.
CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT
Check the fuel level sensor signal circuit. Refer to
MWI-68, "Component Function Check"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст