Nissan Qashqai J11. Manual — part 877
WT-54
< SYMPTOM DIAGNOSIS >
[WITH TPMS]
TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE COMPLETED
TIRE PRESSURE SENSOR ID REGISTRATION CANNOT BE COMPLETED
Description
INFOID:0000000010339563
The ID of the tire pressure sensor installed in each wheel cannot be registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring system circuit.
Diagnosis Procedure
INFOID:0000000010339564
1.
CHECK TIRE PRESSURE SENSOR INSTALLATION
Check visually that tire pressure sensors are installed to each wheels correctly.
NOTE:
In the following case, tire pressure monitoring system (TPMS) does not function.
• Tire pressure sensor(s) are not installed.
• Tire pressure sensor(s) of other cars are installed.
Are the genuine NISSAN tire pressure sensors are installed correctly?
YES
>> GO TO 2.
NO
>> Replace and/or Install tire pressure sensor(s). Refer to
WT-62, "Removal and Installation"
. GO TO
3.
2.
CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL
Check tire pressure sensor activation tool.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the battery of tire pressure sensor activation tool or repair/replace the tire pressure sen-
sor activation tool.
3.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
Is tire pressure sensor ID registration completed?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
CHECK TIRE PRESSURE SIGNAL
Change the work location and perform ID registration again.
NOTE:
Depending on the tire pressure sensor position*, a blind spot exists, and the tire pressure receiver gets a
poor reception. If an ID registration is performed under this condition, the registration may not be completed.
In such case, follow the instructions below to improve the radio wave receiving environment.
• Rotate tire by 90
°
, 180
°
, or 270
°
. (This step is to change tire pressure sensor position.)
• Open the door close to the tire of which ID registration is ongoing.
*: Radio wave reception condition depends on vehicle architecture (e.g. body harness layout, tire wheel
design) or environment.
When ID registration is performed, which wheels do not react?
All wheels react and ID registration is possible.>>INSPECTION END
Only certain wheel(s) do not react.>>Replace applicable tire pressure sensor. Refer to
All wheels do not react.>>Replace the BCM. Refer to
HAZARD WARNING LAMP REMAINS ON
WT-55
< SYMPTOM DIAGNOSIS >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
HAZARD WARNING LAMP REMAINS ON
Description
INFOID:0000000010339565
The hazard warning lamp remains on.
Diagnosis Procedure
INFOID:0000000010339566
1.
CHECK HAZARD WARNING LAMP OPERATION
Check hazard warning lamp operation with hazard switch.
Is the operation normal?
YES
>> GO TO 2.
NO
>> Perform trouble diagnosis for the hazard warning lamp. Refer to
EXL-143, "Diagnosis Procedure"
EXL-299, "Diagnosis Procedure"
(halogen headlamp).
2.
CHECK HAZARD REQUEST SIGNAL CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect the hazard warning switch connector and BCM harness connector.
3.
Check the continuity between the BCM harness connector and the ground.
Is the inspection result normal?
YES
>> Replace the BCM. Refer to
BCS-132, "Removal and Installation"
.
NO
>> Repair or replace harness or connector.
BCM
—
Continuity
Connector
Terminal
M13
36
Ground
Not existed
WT-56
< SYMPTOM DIAGNOSIS >
[WITH TPMS]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000010339567
Use the chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
(Al
u
mi
nu
m
whe
e
l)
(S
te
el
whe
e
l)
(Al
u
mi
nu
m
whe
e
l)
(S
te
el
whe
e
l)
—
—
NVH in DLN
section.
NVH in DLN
section.
NVH in F
AX and FSU sections.
NVH in RAX
and RSU sections.
Ref
e
r to
TI
RE in
th
is ch
art
.
Ref
e
r to
ROAD WHE
E
L i
n
t
h
is cha
rt.
NVH in F
AX, RAX
section.
NVH in BR section.
NVH in ST section.
Possible cause and SUSPECTED PARTS
Im
p
rop
er i
n
s
ta
lla
ti
o
n
, lo
os
en
es
s
Out
-of-ro
un
d
Un
ba
la
nc
e
Incorrect t
ire
pressure
Uneven tire
wear
Def
o
rm
ati
o
n
o
r da
ma
ge
No
n-u
n
if
ormi
ty
In
co
rrec
t t
ire
si
ze
PROPELLER SHAFT
DIFF
ERENTIAL
FRONT A
X
LE
AND FRONT SUSP
ENSION
REAR A
X
LE
AND REAR SUSP
ENSION
TI
RE
ROAD WHEE
LS
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
TIRE
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
Shimmy, Judder
×
×
×
×
×
×
×
×
×
Poor quality ride or
handling
×
×
×
×
×
×
×
ROAD WHEEL
WT-57
< PERIODIC MAINTENANCE >
[WITH TPMS]
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PERIODIC MAINTENANCE
ROAD WHEEL
Inspection
INFOID:0000000010339568
APPEARANCE
Road Wheel
• Check road wheel for deformation, cracks, corrosion and other damage.
• Check wheel nuts for looseness by using torque wrench.
Tire
• Check entire circumference and both sides of each tire for deformation, cracks, scratch and other damage.
• Check tire tread for wear and foreign matter such as nails and small rock.
• Check that tire pressure is the specified value.
Wheel Balance Adjustment (Aluminum Wheel)
INFOID:0000000010339569
PREPARATION BEFORE ADJUSTMENT
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
• Never scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
ADJUSTMENT
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for aluminum wheels.
1.
Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
• Never install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, always to clean the mating surface of the road wheel.
a.
Indicated unbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz)
⇒
40 g (1.41 oz) bal-
ance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒
35 g (1.23 oz)
37.5
⇒
40 g (1.41 oz)
b.
Installed balance weight in the position.
Wheel nut tightening torque
: Refer to
.
Tire pressure
: Refer to
SMA054D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст