Nissan Qashqai J11. Manual — part 1803
WW-90
< REMOVAL AND INSTALLATION >
HEADLAMP WASHER
Hydraulic Layout
INFOID:0000000010479841
WASHER NOZZLE
WASHER NOZZLE : Removal and Installation
INFOID:0000000010479842
REMOVAL
1.
Remove front bumper fascia assembly. Refer to
EXT-19, "Removal and Installation"
2.
Disengage headlamp washer cover fixing pawls while pull out headlamp washer nozzle from front bumper
fascia assembly, and then remove headlamp washer cover.
3.
Remove headlamp washer nozzle.
a.
Pull out washer tube from washer nozzle.
b.
Disengage headlamp washer bracket fixing pawl, and then remove headlamp washer bracket from front
bumper fascia assembly.
c.
Separate headlamp washer bracket and headlamp washer nozzle.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• After installation, check that there is no leakage at operated washer.
• After installation, check spray position. Refer to
WW-90, "WASHER NOZZLE : Inspection"
WASHER NOZZLE : Inspection
INFOID:0000000010479843
HEADLAMP WASHER NOZZLE SPRAY POSITION INSPECTION
Check that washer fluid is sprayed on the luminescent surface of lamp.
CAUTION:
Headlamp washer nozzle
Washer tank
Washer tank
: Fixing portion
JMLIA5166ZZ
HEADLAMP WASHER
WW-91
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Replace headlamp washer nozzle assembly with a new part if headlamp washer jet position is outside
the headlamp illumination area.
WASHER TUBE
WASHER TUBE : Removal and Installation
INFOID:0000000010479844
REMOVAL
1.
Remove front bumper fascia assembly. Refer to
EXT-19, "Removal and Installation"
.
2.
Pull out washer tube from headlamp washer nozzle.
3.
Disengage headlamp washer tube fixing portion, and then remove headlamp washer tube.
INSTALLATION
Note the following item, and then Install in the reverse order of removal.
CAUTION:
After installation, check that there is no leakage at operated washer.
WASHER PUMP
WASHER PUMP : Removal and Installation
INFOID:0000000010479845
REMOVAL
CAUTION:
When the washer tube and washer pump is removed, washer fluid may come out so prepare a con-
tainer to receive the fluid and never allow fluid to be sprinkled.
1.
Remove front fender protector. Refer to
EXT-32, "Removal and Installation"
.
2.
Pull out washer tube from washer pump.
3.
Disconnect washer pump harness connector, pull out washer pump, and then remove washer pump.
4.
Remove packing.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check that packing is inserted fully. (This may be the cause of washer fluid leakage and washer
pump looseness.)
• Add washer liquid up to the top of the washer tank inlet after installing. Check that there is no leak-
age.
• After installation, check that there is no leakage at operated washer.
WW-92
< REMOVAL AND INSTALLATION >
RAIN SENSOR
RAIN SENSOR
Exploded View
INFOID:0000000010479846
Removal and Installation
INFOID:0000000010479847
REMOVAL
1.
Remove inside mirror cover. Refer to
2.
Disconnect rain sensor harness connector.
3.
Disengage rain sensor fixing lock spring portion
, and then
Peel off rain sensor.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Replace rain sensor with a new part after removal. Never reuse rain sensor.
• Clean the sensor installation portion of the windshield.
• When the sensor is removed, wipe off the silicon pad remaining on the windshield surface.
Rain sensor
: Always replace after every disassembly.
JMLIA5167ZZ
JMLIA4203ZZ
RAIN SENSOR
WW-93
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
• Remove the sensor protective cover just before installation.
Never touch the silicon pad
after removal of sensor protec-
tive cover.
• Install the rain sensor so that the connector faces vehicle upward.
• When installing, never allow silicon pad to touch the sensor bracket and other parts.
• Compress the lock spring portion
vertically to the glass
surface and fully engage both ends of lock spring.
• Never use a sensor that is dropped.
• Perform check after replacement. Refer to
.
Inspection
INFOID:0000000010479848
CAUTION:
Clean the windshield glass and wiper refill so that the windshield glass may not be damaged by dust,
etc.
1.
Push the ignition switch to the ON position, and set the combination switch to AUTO.
2.
Spray water mist toward the sensor.
3.
Check that wiper operates.
• If the wiper does not operate, check the connection of the connector. Refer to
.
• If there is no malfunction in the connection, replace the sensor.
JMLIA4204ZZ
JMLIA4205ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст