Nissan Qashqai J11. Manual — part 606
CL-30
< UNIT REMOVAL AND INSTALLATION >
CLUTCH DISC AND CLUTCH COVER
p.
Install transaxle assembly to the vehicle. Refer to
TM-88, "Removal and Installation"
R9M : Inspection
INFOID:0000000010288581
INSPECTION AFTER REMOVAL
CLUTCH DISC
• Measure circumferential runout relative to clutch disc center spline.
If it is outside the specification, replace clutch disc.
• Measure backlash to clutch disc spline and main drive gear spline
at the circumference of clutch disc. If outside the specification,
replace clutch disc.
• Measure the depth “A” to clutch disc facing rivet heads using cali-
pers. If it exceeds the allowable facing wear limit, replace clutch
disc.
CLUTCH COVER
Check diaphragm spring lever claws for unevenness with the lever
still on the vehicle. If they exceed the tolerance, adjust lever height
using the diaphragm adjusting wrench [SST: ST20050240].
• Check clutch cover thrust ring for wear or breakage. If wear or
breakage is found, replace clutch cover.
NOTE:
• Worn thrust ring will generate a beating noise when tapped at the
rivet with a hammer.
• Broken thrust ring will make a clinking sound when cover is
shaken up and down.
• If a trace of burn or discoloration is found on the clutch cover pressure plate to clutch disc contact surface,
repair the surface with sandpaper. If surface is damaged or distorted, replace clutch cover.
Runout limit/diameter of the
area to be measured
: Refer to
.
Maximum allowable spline
backlash (at outer edge of disc)
: Refer to
.
Facing wear limit (depth to the
rivet head)
: Refer to
.
SCL221
JPDIB0026ZZ
Tolerance for diaphragm
spring lever unevenness
: Refer to
PCIB0276E
SERVICE DATA AND SPECIFICATIONS (SDS)
CL-31
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
E
F
G
H
I
J
K
L
M
A
B
CL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Clutch Control System
INFOID:0000000010288582
Clutch Pedal
INFOID:0000000010288583
Unit: mm (in)
Clutch Disc
INFOID:0000000010288584
Unit: mm (in)
Clutch Cover
INFOID:0000000010288585
Type of clutch control
Hydraulic
Clearance “A” between clutch pedal and ASCD switch threaded
end while clutch pedal is fully released.
0.2 - 1.96 (0.008 - 0.0772)
Clearance “B” between clutch pedal and Interlock switch threaded
end while clutch pedal is fully released.
0.2 - 1.96 (0.008 - 0.0772)
Engine type
HRA2DDT
K9K
R9M
MR20DD
Model
225
240
230
Facing size (Outer dia.
×
Inner
dia.
×
Thickness)
225
×
150
×
2.9 (8.9
×
5.91
×
0.114)
225
×
150
×
2.9 (8.9
×
5.91
×
0.114)
239
×
170
×
3.45 (9.41
×
6.69
×
0.1358)
230
×
155
×
3.2
(9.06
×
6.10
×
0.126)
Runout limit/diameter of the
area to be measured
1.0 (0.039) /215 (8.46)
dia.
1.0 (0.039) /215 (8.46)
dia.
1.0 (0.039) /230 (9.06)
dia.
1.0 (0.039) /240 (9.45)
dia.
Maximum allowable spline
backlash (at outer edge of disc)
1.2 (0.047)
1.28 (0.0504)
0.9 (0.035)
Facing wear limit (depth to the
rivet head)
replace if worn to rivet head
0.3 (0.012)
Engine type
HRA2DDT
K9K
MR20DD
R9M
Transaxle type
RS6F94R
RS6F52A (4WD)
RS6F95R (2WD)
Set-load
5,730 N (584.5 kg,
1,288.1 lb)
7,100 N (724.2 kg,
1416.2 lb)
5,700 N (581.4 kg,
1,281.4 lb)
8,800 N (897.6 kg, 1978.2 lb)
Tolerance for diaphragm
spring lever unevenness
1.2 mm (0.047 in) or less
not specified
0.8 mm (0.031 in) or less
Diaphragm spring lever
height (new clutch)
12.6 - 16.2 mm
(0.496 - 0.64 in)
12.8 - 14.8 mm
(0.504 - 0.583 in)
20.7 - 22.7 (0.815 -
0.8937)
26.6 - 29.0 mm (1.047 - 1.142 in)
TM-1
TRANSMISSION & DRIVELINE
C
E
F
G
H
I
J
K
L
M
SECTION
TM
A
B
TM
N
O
P
CONTENTS
TRANSAXLE & TRANSMISSION
6MT: RS6F94R
SYSTEM DESCRIPTION . . . . . . . .
M/T SYSTEM . . . . . . . . . . . . . ..
System Diagram . . . . . . . . . . . . . ..
System Description . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
POSITION SWITCH . . . . . . . . . . .
BACK-UP LAMP SWITCH . . . . . . . . . .
BACK-UP LAMP SWITCH : Component Parts Lo-
cation . . . . . . . . . . . . . . . . . ...
BACK-UP LAMP SWITCH : Component Inspec-
tion . . . . . . . . . . . . . . . . . . ..
PARK/NEUTRAL POSITION (PNP) SWITCH . . ...
PARK/NEUTRAL POSITION (PNP) SWITCH :
Component Parts Location . . . . . . . . . ..
PARK/NEUTRAL POSITION (PNP) SWITCH :
Component Inspection . . . . . . . . . . .
SYMPTOM DIAGNOSIS . . . . . . . ..
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . .
PRECAUTION . . . . . . . . . . . ..
PRECAUTIONS . . . . . . . . . . . . ..
Precaution for Procedure without Cowl Top Cover
Service Notice or Precautions for Manual Tran-
saxle . . . . . . . . . . . . . . . . . .
Precautions for Removing Battery Terminal . . ...
PREPARATION . . . . . . . . . . ...
PREPARATION . . . . . . . . . . . . ..
Special Service Tools . . . . . . . . . . .
Commercial Service Tools . . . . . . . . . .
PERIODIC MAINTENANCE . . . . . .
GEAR OIL . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Draining . . . . . . . . . . . . . . . . ...
Refilling . . . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
M/T SHIFT SELECTOR . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CONTROL LINKAGE . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SIDE OIL SEAL . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
AIR BREATHER HOSE . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT REMOVAL AND INSTALLATION . ..
TRANSAXLE ASSEMBLY . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
TRANSAXLE ASSEMBLY . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Disassembly . . . . . . . . . . . . . . .
Assembly . . . . . . . . . . . . . . . . .
INPUT SHAFT AND GEAR . . . . . . . ...
Exploded View . . . . . . . . . . . . . . .
TM-2
Assembly . . . . . . . . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
MAINSHAFT AND GEAR . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ....
Disassembly . . . . . . . . . . . . . . ...
Assembly . . . . . . . . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
REVERSE IDLER SHAFT AND GEAR . . . .
Exploded View . . . . . . . . . . . . . ....
Disassembly . . . . . . . . . . . . . . ...
Assembly . . . . . . . . . . . . . . . ....
FINAL DRIVE . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Disassembly . . . . . . . . . . . . . . ...
Assembly . . . . . . . . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
SHIFT FORK AND FORK ROD . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Disassembly . . . . . . . . . . . . . . ...
Assembly . . . . . . . . . . . . . . . ....
Inspection . . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . ..
General Specification . . . . . . . . . . . .
6MT: RS6F95R
SYSTEM DESCRIPTION . . . . . . .
M/T SYSTEM . . . . . . . . . . . . . .
System Diagram . . . . . . . . . . . . . .
System Description . . . . . . . . . . . . .
DTC/CIRCUIT DIAGNOSIS . . . . . . .
POSITION SWITCH . . . . . . . . . . ...
BACK-UP LAMP SWITCH . . . . . . . . . ....
BACK-UP LAMP SWITCH : Component Parts Lo-
cation . . . . . . . . . . . . . . . . . ..
BACK-UP LAMP SWITCH : Component Inspec-
tion . . . . . . . . . . . . . . . . . . ..
PARK/NEUTRAL POSITION (PNP) SWITCH . . ..
PARK/NEUTRAL POSITION (PNP) SWITCH :
Component Parts Location . . . . . . . . . .
PARK/NEUTRAL POSITION (PNP) SWITCH :
Component Inspection . . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . .
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING . . . . . . .
NVH Troubleshooting Chart . . . . . . . . ...
PRECAUTION . . . . . . . . . . .
PRECAUTIONS . . . . . . . . . . . . .
Precaution for Procedure without Cowl Top Cover ...
Precautions for Removing Battery Terminal . . ...
Service Notice or Precautions for Manual Tran-
saxle . . . . . . . . . . . . . . . . . .
PREPARATION . . . . . . . . . . ..
PREPARATION . . . . . . . . . . . . .
Special Service Tools . . . . . . . . . . .
Commercial Service Tools . . . . . . . . .
PERIODIC MAINTENANCE . . . . . ...
GEAR OIL . . . . . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Draining . . . . . . . . . . . . . . . . ...
Refilling . . . . . . . . . . . . . . . . ...
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ..
DIFFERENTIAL OUTPUT SEAL . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
CONTROL LINKAGE . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
AIR BREATHER HOSE . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT REMOVAL AND INSTALLATION .
TRANSAXLE ASSEMBLY . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY ...
TRANSAXLE ASSEMBLY . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Disassembly . . . . . . . . . . . . . . .
Assembly . . . . . . . . . . . . . . . ..
INPUT SHAFT AND GEAR . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Disassembly . . . . . . . . . . . . . . ..
Assembly . . . . . . . . . . . . . . . ..
Adjustment . . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . ..
MAINSHAFT AND GEAR . . . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Disassembly . . . . . . . . . . . . . . ..
Assembly . . . . . . . . . . . . . . . ..
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст