Nissan Qashqai J11. Manual — part 633
TRANSAXLE ASSEMBLY
TM-107
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F95R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
24. Slightly raise forks 1-2 and 3-4 and 5-6 and fit the control mod-
ule.
25. Pivot the module anti-clockwise until the claw of the reverse
gear shaft is freed from any restriction.
Place:
• the part (1) of the control module in neutral,
• the reverse gear shaft in neutral.
26. Raise the spring (1) , pivot the control module and pass the
return spring over the return pin (2) .
27. Check that the spring (1) is securely seated in the groove of the
return pin (2) .
28. Refit:
E1DIA0281ZZ
E1DIA0282ZZ
E1DIA0283ZZ
E1DIA0330ZZ
TM-108
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F95R]
TRANSAXLE ASSEMBLY
• the output shaft adjusting shim,
• the new stop ring (1) .
29. Refit the deflector (1) and the adjusting shim (2) at the end of the
input shaft.
30. Refit the oil neck (1) , making sure that the lug (2) is properly
positioned in its housing.
31. Refit the oil neck (1) by positioning the lug (2) and the two cen-
tring pins (3) in their housings.
32. Check that the centring dowels are in place.
WARNING:
Applying excess sealant could cause it to be squeezed out when parts are tightened. A mixture of
sealant and fluid may cause damage to some components.
E1DIA0262ZZ
E1DIA0263ZZ
E1DIA0264ZZ
E1DIA0265ZZ
TRANSAXLE ASSEMBLY
TM-109
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F95R]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
33. Apply a bead of SILICONE ADHESIVE SEALANT all around the
joint face of the mechanism housing as shown on the figure.
34. Position the mechanism housing temporarily with the gear lever
(1) turned.
35. Refit the mechanism housing while rotating the gear lever (1) .
36. Widen the stop ring (1) at the level of the output shaft rear bear-
ing in such a way that the stop ring comes into contact with the
edge of the output shaft rear bearing.
E1DIA0331ZZ
E1DIA0266ZZ
E1DIA0267ZZ
E1DIA0268ZZ
TM-110
< UNIT DISASSEMBLY AND ASSEMBLY >
[6MT: RS6F95R]
TRANSAXLE ASSEMBLY
37. Pretighten the mechanism housing bolts following the order as
shown on the figure.
38. Position:
• the gear lever in 2nd gear,
• the stop ring in the bearing channel of the output shaft.
39. Check that:
• the stop ring (1) is in the bearing channel of the output shaft,
• the adjusting shim (2) rotates freely in its housing and is not secured..
40. Tighten the mechanism housing bolts following the order as
shown on the figure.
41. Refit the selector lever seal using component (D) of the tool [Bvi.
1902].
42. Put the gear lever in neutral.
43. Refit:
• a new blanking cover (1),
• the gear lever (2),
• a new selector lever pin (3),
• the new dual function switch (4) coated with RESIN ADHE-
MA-59, "Fluids and Lubricants"
: 35 N.m (3.6 kg-m; 26 ft-lb)
E1DIA0332ZZ
: 52 N.m (5.3 kg-m; 38 ft-lb)
E1DIA0332ZZ
E1DIA0269ZZ
E1DIA0270ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст