Nissan Maxima. Manual — part 1028
FRONT SEAT
SE-85
< UNIT DISASSEMBLY AND ASSEMBLY >
[WITH CLIMATE CONTROLLED SEATS]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PASSENGER SIDE : Exploded View
INFOID:0000000009468153
Passenger Seat
AWJIA0926ZZ
1.
Seatback board
2.
Seatback board clips
3.
Headrest
4.
Seat harness
5.
Seat cushion inner finisher inside (RH) 6.
Recline device inner cover
7.
Seat cushion outer finisher (RH) 8.
Seat recline knob
9.
Seat slide and lifter switch knob
10.
Power seat switch
11.
Seat cushion assembly
12. Seat cushion front finisher
13.
Front slide cover
14.
Seat frame assembly
15. Seat cushion outer finisher (LH)
16
Recline mechanism inner cover
17.
Seat cushion inner finisher inside (LH) 18. Seat belt buckle
19.
Seatback assembly
20.
Seatback pad
21. Seatback trim
SE-86
< UNIT DISASSEMBLY AND ASSEMBLY >
[WITH CLIMATE CONTROLLED SEATS]
FRONT SEAT
PASSENGER SIDE : Disassembly and Assembly
INFOID:0000000009468154
SEAT ASSEMBLY WITH SIDE AIR BAG MODULE
WARNING:
Do not leave any objects (screwdriver, tools, etc.) on the seat during seatback repair. It can lead to per-
sonal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least 3
minutes.
• Handle the side air bag module carefully. During disassembly, always hold the side air bag module,
do not let it hang by the wire harness.
• Always place side air bag module with the stud bolt side facing downward.
• Always work from the side or back of the seatback assembly, do not work in front of seat.
• Do not use air tools or electric tools when servicing the seat assembly.
• Replace the side air bag module if it has been dropped or sustained an impact.
• Do not insert any objects into the side air bag module.
• Do not disassemble the side air bag module.
• Do not expose the side air bag module to temperatures exceeding 93
°C (200°F).
• Do not expose the side air bag module to any oil, grease or water.
• During disassembly, do not damage the trim cover, chutes, connectors, retainers, clips, module har-
ness or the side air bag module.
NOTE:
• If the vehicle has been involved in a collision and the side air bag has deployed, the front seatback assembly
must be replaced.
• For side air bag module removal and installation, refer to
SR-21, "Removal and Installation"
Disassembly
1. Remove the front seat assembly. Refer to
SE-68, "Removal and Installation"
.
2. Remove the seatback board as follows:
NOTE:
The seatback board is attached to the seat frame with the follow-
ing:
• Two top hooks (A)
• Two side hooks (B)
• Two bottom retainers (C)
a. From the bottom of the seat, unhook the two seat skirt hooks as
shown.
22.
Seatback frame
23.
Chute rod
24. Side air bag module
25.
Rear slide cover
26.
Headrest holder (locked)
27. Headrest holder (free)
ALJIA0587ZZ
ALJIA0588ZZ
FRONT SEAT
SE-87
< UNIT DISASSEMBLY AND ASSEMBLY >
[WITH CLIMATE CONTROLLED SEATS]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
b. Carefully pull upward on the lower seatback board to release the
two bottom retainers (C).
CAUTION:
Do not pull outward at two top hooks (A).
c. Hold the seatback board at the side hook locations (B) and push
in the side hooks to release them from the seatback frame, then
pull it rearward.
d. Carefully pull the seatback board downward to disengage the
top hooks as shown.
CAUTION:
Use care not to break the seatback board hooks and retain-
ers. Replace seatback board if any hooks or retainers are
damaged.
3. Remove and discard the two chute rod bolts (A), then remove
the chute rod (1).
CAUTION:
Do not reuse the chute rod bolts.
4. Release the seven seatback retainers from the seatback frame
as shown.
5. Reach in from the bottom of the seatback to release the guide
clips on the headrest holder. Squeeze the clips at the bottom
and push upward to remove as shown.
ALJIA0587ZZ
ALJIA0589ZZ
Chute rod bolts (A)
: 8.2 N·m (0.84 kg-m, 73 in-lb)
ALJIA0590ZZ
ALJIA0598ZZ
PIIB4084J
SE-88
< UNIT DISASSEMBLY AND ASSEMBLY >
[WITH CLIMATE CONTROLLED SEATS]
FRONT SEAT
6. Disconnect the harness connector for the seatback heater.
7. Push the seatback trim and seatback pad forward at the bottom
(1), then holding the seatback assembly on both sides, lift
upward (2). Remove the seatback trim and seatback pad as an
assembly from the seatback frame.
8. If required, separate the seatback trim from the seatback pad as
follows:
NOTE:
The seatback trim is attached to the seatback pad with the fol-
lowing:
• Five top hog rings (A)
• Three side hog rings (B)
• Three middle hog rings (C)
• Three bottom velcro fasteners (D)
a. Pull the seatback trim cover from the seatback pad to detach the
velcro fasteners.
b. Position the seatback trim to access the middle hog rings.
Remove the middle and side hog rings.
c.
Remove the top hog rings, then separate the seatback trim from
the seatback pad.
Assembly
Assembly is in the reverse order of disassembly. During assembly, note the following.
ALJIA0599ZZ
ALJIA0594ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст