Nissan Maxima. Manual — part 763
DIAGNOSIS SYSTEM (BCM)
INL-11
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010051378
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
INT LAMP
Direct Diagnostic Mode
Description
Ecu Identification
The BCM part number is displayed.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Work support
Changes the setting for each system function.
Configuration
• Enables to read and save the vehicle specification.
• Enables to write the vehicle specification when replacing BCM.
CAN Diag Support Mntr
Monitors the reception status of CAN communication viewed from BCM.
System
Sub System
Direct Diagnostic Mode
E
cu
Id
en
tifi
ca
tio
n
Se
lf Di
ag
no
st
ic Re
su
lt
Da
ta
Mo
ni
tor
A
cti
ve
T
est
W
o
rk support
Co
nf
igu
rat
ion
CA
N Diag
Su
pp
ort Mn
tr
Door lock
DOOR LOCK
×
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEADLAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps FLASHER
×
×
×
Intelligent Key system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
BCM
BCM
×
×
×
×
×
Immobilizer
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Trunk open
TRUNK
×
×
Vehicle security system
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
×
INL-12
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
INT LAMP : CONSULT Function (BCM - INT LAMP)
INFOID:0000000010051379
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
Monitor Item [Unit]
Description
REQ SW -DR [On/Off]
Indicates condition of door request switch LH
REQ SW -AS [On/Off]
Indicates condition of door request switch RH
PUSH -SW [On/Off]
Indicates condition of push button ignition switch
ACC RLY -F/B [ON/OFF]
Indicates condition of accessory relay
UNLK SEN -DR [On/Off]
Indicates condition of door unlock sensor
KEY SW -SLOT [On/Off]
Indicates condition of key slot
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH
DOOR SW-RR [On/Off]
Indicates condition of rear door switch RH
DOOR SW-RL [On/Off]
Indicates condition of rear door switch LH
DOOR SW-BK [On/Off]
Indicates condition of trunk switch
CDL LOCK SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch
CDL UNLOCK SW [On/Off]
Indicates condition of unlock signal from door lock and unlock switch
KEY CYL LK-SW [On/Off]
Indicates condition of lock signal from door key cylinder switch
KEY CYL UN-SW [On/Off]
Indicates condition of unlock signal from door key cylinder switch
TRNK/HAT MNTR [ON/OFF]
Indicates condition of trunk room lamp switch
RKE-LOCK [On/Off]
Indicates condition of lock signal from Intelligent Key
RKE-UNLOCK [On/Off]
Indicates condition of unlock signal from Intelligent Key
Test Item
Description
INT LAMP
This test is able to check interior room lamp operation [On/Off].
STEP LAMP TEST
This test is able to check step lamp operation [On/Off].
LUGGAGE LAMP TEST
This test is able to check trunk room lamp operation [On/Off].
Support Item
Setting
Description
SET I/L D-UNLCK INTCON
On*
Interior room lamp timer function ON
Off
Interior room lamp timer function OFF
ROOM LAMP TIMER SET
MODE 4
30 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 3* 15 sec.
MODE 2
7.5 sec.
ROOM LAMP ON TIME SET
MODE 5
0 sec.
Sets the interior room lamp gradual brightening time.
MODE 4
3 sec.
MODE 3
2 sec.
MODE 2* 1 sec.
MODE 1
0.5 sec.
DIAGNOSIS SYSTEM (BCM)
INL-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
INL
N
O
P
* : Initial setting
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000010051380
DATA MONITOR
ACTIVE TEST
WORK SUPPORT
ROOM LAMP OFF TIME SET
MODE 5
0 sec.
Sets the interior room lamp gradual dimming time.
MODE 4* 3 sec.
MODE 3
2 sec.
MODE 2
1 sec.
MODE 1
0.5 sec.
R LAMP TIMER LOGIC SET
MODE 2
Interior room lamp timer activates with all doors.
MODE 1*
Interior room lamp timer activates with the driver door only.
Support Item
Setting
Description
Monitor Item [Unit]
Description
REQ SW -DR [On/Off]
Indicates condition of door request switch LH
REQ SW -AS [On/Off]
Indicates condition of door request switch RH
PUSH SW [On/Off]
Indicates condition push button ignition switch
ACC RLY -F/B [On/Off]
Indicates condition of accessory relay
UNLK SEN -DR [On/Off]
Indicates condition of door unlock sensor
KEY SW -SLOT [On/Off]
Indicates condition of key slot
DOOR SW-DR [On/Off]
Indicates condition of front door switch LH
DOOR SW-AS [On/Off]
Indicates condition of front door switch RH
DOOR SW-RR [On/Off]
Indicates condition of rear door switch RH
DOOR SW-RL [On/Off]
Indicates condition of rear door switch LH
DOOR SW-BK [On/Off]
Indicates condition of trunk switch
CDL LOCK SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch
CDL UNLOCK SW [On/Off]
Indicates condition of unlock signal from door lock and unlock switch
KEY CYL LK-SW [On/Off]
Indicates condition of lock signal from door key cylinder switch
KEY CYL UN-SW [On/Off]
Indicates condition of unlock signal from door key cylinder switch
TRNK/HAT MNTR [On/Off]
Indicates condition of trunk room lamp switch
RKE-LOCK [On/Off]
Indicates condition of lock signal from Intelligent Key
RKE-UNLOCK [On/Off]
Indicates condition of unlock signal from Intelligent Key
Test item
Description
BATTERY SAVER
This test is able to check battery saver operation [On/Off].
Support Item
Setting
Description
ROOM LAMP BAT SAV SET
ON*
Interior room lamp battery saver function ON
OFF
Interior room lamp battery saver function OFF
ROOM LAMP TIMER SET
MODE 3*
10 min.
Sets interior room lamp battery saver timer operating time
MODE 2
60 min.
MODE 1
15 min.
INL-14
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
* : Initial setting
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)
INFOID:0000000010051381
DATA MONITOR
BATTERY SAVER SET
ON*
Exterior lamp battery saver function ON
OFF
Exterior lamp battery saver function OFF
Support Item
Setting
Description
Monitor Item [Unit]
Main
Description
REQ SW -DR [On/Off]
×
Indicates condition of door request switch LH
REQ SW -AS [On/Off]
×
Indicates condition of door request switch RH
REQ SW -BD/TR [On/Off]
×
Indicates condition of trunk opener request switch
PUSH SW [On/Off]
Indicates condition of push button ignition switch
IGN RLY2 -F/B [On/Off]
Indicates condition of ignition relay 2
ACC RLY -F/B [On/Off]
Indicates condition of accessory relay
BRAKE SW 1 [On/Off]
×
Indicates condition of brake switch
BRAKE SW 2 [On/Off]
Indicates condition of brake switch
DETE/CANCL SW [On/Off]
×
Indicates condition of P position
SFT PN/N SW [On/Off]
×
Indicates condition of P or N position
UNLK SEN -DR [On/Off]
×
Indicates condition of door unlock sensor
PUSH SW -IPDM [On/Off]
Indicates condition of push button ignition switch received from IPDM E/R on
CAN communication line
IGN RLY1 -F/B [On/Off]
Indicates condition of ignition relay 1 received from IPDM E/R on CAN commu-
nication line
DETE SW -IPDM [On/Off]
Indicates condition of detent switch received from TCM on CAN communication
line
SFT PN -IPDM [On/Off]
Indicates condition of P or N position from TCM on CAN communication line
SFT P -MET [On/Off]
Indicates condition of P position from TCM on CAN communication line
SFT N -MET [On/Off]
Indicates condition of N position from IPDM E/R on CAN communication line
ENGINE STATE [Stop/Start/Crank/Run]
×
Indicates condition of engine state from ECM on CAN communication line
VEH SPEED 1 [mph/km/h]
×
Indicates condition of vehicle speed signal received from ABS on CAN commu-
nication line
VEH SPEED 2 [mph/km/h]
×
Indicates condition of vehicle speed signal received from combination meter on
CAN communication line
DOOR STAT -DR [LOCK/READY/UNLK]
×
Indicates condition of driver side door status.
DOOR STAT -AS [LOCK/READY/UNLK]
×
Indicates condition of passenger side door status.
ID OK FLAG [Set/Reset]
Indicates condition of Intelligent Key ID.
PRMT ENG STRT [Set/Reset]
Indicates condition of engine start possibility.
PRMT RKE STRT [Set/Reset]
Indicates condition of engine start possibility from Intelligent Key.
KEY SW -SLOT [On/Off]
Indicates condition of key slot.
TRNK/HAT MNTR [On/Off]
Indicates condition of trunk lid.
RKE-LOCK [On/Off]
Indicates condition of lock signal from Intelligent Key.
RKE-UNLOCK [On/Off]
Indicates condition of unlock signal from Intelligent Key.
RKE-TR/BD [On/Off]
Indicates condition of trunk open signal from Intelligent Key.
RKE-PANIC [On/Off]
Indicates condition of panic signal from Intelligent Key.
RKE-P/W OPEN [On/Off]
Indicates condition of power window down signal from Intelligent Key.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст