Nissan Maxima. Manual — part 655
ROOF SIDE MOLDING
EXT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
ROOF SIDE MOLDING
Exploded View
INFOID:0000000009465820
Removal and Installation
INFOID:0000000009465821
REMOVAL
1. Using suitable tool, lift and twist the roof side molding up from the rear edge, working forward.
2. Disengage each roof side molding clip, then remove the roof side molding.
INSTALLATION
Installation is in the reverse order of removal.
• Begin with aligning rear end of the roof molding with top edge of rear window glass molding. Refer to
14, "Removal and Installation"
Clip Replacement
INFOID:0000000009465822
REMOVAL
1. Remove roof side molding.
2. Heat adhesive tape interface using a suitable tool (heat gun), then peel roof side molding clips (body side)
using long-nose pliers.
CAUTION:
Be careful not to damage the body.
INSTALLATION
1.
Roof side molding
2.
Roof panel
3.
Body side panel
B.
Roof side molding clip
ALKIA2270ZZ
EXT-30
< REMOVAL AND INSTALLATION >
ROOF SIDE MOLDING
1. Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2. Use two-part epoxy adhesive.
3. Apply adhesive evenly to clip tape surface.
4. Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to
tape side.
5. Tape clips after press fit, and temporarily hold it for specified time based on the following.
6. Install roof side molding rear edge first, working toward front after temporarily holding.
CAUTION:
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding, check that molding fastener is securely inserted and then press
in.
• Do not wash the vehicle within 24 hours after repair.
Adhesive
: 3M-weld DP–100 or equivalent
Thickness
: Approximately 0.5 mm (0.020 in)
Press-fit limit : 19.6 N
× 2 seconds
5 to 10
°C (41 to 50°F)
: 1 hour or more
11 to 23
°C (52 to 73°F)
: 30 minutes or more
24
°C or more (75°F or more)
: 15 minutes or more
LICENSE LAMP FINISHER
EXT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
LICENSE LAMP FINISHER
Exploded View
INFOID:0000000009465823
Removal and Installation
INFOID:0000000009465824
REMOVAL
1. Remove the trunk lid finisher. Refer to
INT-36, "Removal and Installation"
2. Disconnect the harness connector (1) from the trunk request
switch.
3. Remove the license lamp finisher nuts.
4. Release the clips, then loosen trunk request switch harness
grommet from trunk.
5. Remove license lamp finisher by pulling out and rearward away
from trunk.
INSTALLATION
Installation is in the reverse order of removal.
1.
License lamp finisher
2.
Trunk request switch connector
3.
Grommet
Clip
ALKIA1590ZZ
ALKIA1591ZZ
EXT-32
< REMOVAL AND INSTALLATION >
REAR SPOILER
REAR SPOILER
Exploded View
INFOID:0000000009465825
Removal and Installation
INFOID:0000000009465826
Removal
1. Remove trunk lid finisher. Refer to
INT-36, "Removal and Installation"
2. Disconnect the harness connector (1) from the high-mounted
stop lamp.
3. Remove the rear spoiler assembly nuts.
1.
Rear spoiler assembly
2.
High-mounted stop lamp harness connector 3.
Harness grommet
AWKIA1562ZZ
ALKIA1593ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст