Nissan Juke (2014 year). Service Repair Manual — part 218
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
SEC-123
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
Description
INFOID:0000000009754710
Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to
.
• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
Power supply position is not the ON position.
Diagnosis Procedure
INFOID:0000000009754711
1.
CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
Refer to
SEC-120, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 October
2014 JUKE
SEC-124
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
VEHICLE SECURITY SYSTEM CANNOT BE SET
INTELLIGENT KEY
INTELLIGENT KEY : Description
INFOID:0000000009754712
Armed phase is not activated when all doors are locked using Intelligent Key.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
INTELLIGENT KEY : Diagnosis Procedure
INFOID:0000000009754713
1.
CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)
Lock/unlock door with Intelligent Key.
Refer to
DLK-21, "REMOTE KEYLESS ENTRY FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description
INFOID:0000000009754714
Armed phase is not activated when all doors are locked using door request switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000009754715
1.
CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door request switch.
Refer to
DLK-17, "DOOR LOCK FUNCTION : System Description"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (door lock function). Refer to
SWITCHES : Diagnosis Procedure"
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
Revision: 2013 October
2014 JUKE
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-125
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
NO
>> GO TO 1.
DOOR KEY CYLINDER
DOOR KEY CYLINDER : Description
INFOID:0000000009754716
ARMED phase is not activated when all doors are locked using mechanical key.
NOTE:
Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and check
each symptom.
CONDITION OF VEHICLE (OPERATING CONDITION)
• SECURITY ALARM SET: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR KEY CYLINDER : Diagnosis Procedure
INFOID:0000000009754717
1.
CHECK POWER DOOR LOCK SYSTEM
Lock or unlock doors using mechanical key.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check power door lock system. Refer to
DLK-100, "Diagnosis Procedure"
.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : Description
INFOID:0000000009754718
Armed phase is not activated when all doors are locked by door lock and unlock switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
DOOR LOCK AND UNLOCK SWITCH : Diagnosis Procedure
INFOID:0000000009754719
1.
CHECK DOOR LOCK FUNCTION
Lock/unlock door using mechanical key inserted into door key cylinder.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 October
2014 JUKE
SEC-126
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
VEHICLE SECURITY ALARM DOES NOT ACTIVATE
Description
INFOID:0000000009754720
Alarm does not operate when alarm operating condition is satisfied.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT.
Diagnosis Procedure
INFOID:0000000009754721
1.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-81, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the malfunctioning door switch
2.
CHECK HEADLAMPS FUNCTION
Check head lamps function.
Refer to
SEC-118, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK HORN FUNCTION
Check horn function.
Refer to
SEC-119, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 October
2014 JUKE
NATS ANTENNA AMP.
SEC-127
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
REMOVAL AND INSTALLATION
NATS ANTENNA AMP.
Removal and Installation
INFOID:0000000009754722
REMOVAL
1.
Remove the cluster lid A. Refer to
IP-13, "Removal and Installation"
.
2.
Remove the NATS antenna amp.
1.
Disengage the NATS antenna amp. (1) fixing pawls using
remover tool.
2.
Pull NATS antenna amp. to remove it from push-button igni-
tion switch (2).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA6573ZZ
Revision: 2013 October
2014 JUKE
SEC-128
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
PUSH-BUTTON IGNITION SWITCH
PUSH-BUTTON IGNITION SWITCH
Removal and Installation
INFOID:0000000009754723
REMOVAL
1.
Remove the NATS antenna amp. Refer to
IP-13, "Removal and Installation"
2.
Remove the push-button ignition switch.
1.
Disengage the push-button ignition switch (1) fixing pawls
using remover tool.
2.
Press the push-button ignition switch to remove it from clus-
ter lid A (2).
INSTALLATION
Install in the reverse order of removal.
: Pawl
JMKIA6574ZZ
Revision: 2013 October
2014 JUKE
PRECAUTIONS
SEC-129
< PRECAUTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009754724
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009754725
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
PIIB3706J
Revision: 2013 October
2014 JUKE
SEC-130
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009754726
Component Description
INFOID:0000000009754727
1.
Combination meter
Refer to
2.
Ignition switch
3.
NATS antenna amp.
(Behind ignition switch)
4.
Remote keyless entry receiver
Refer to
5.
ABS actuator and electric unit (con-
trol unit)
Refer to
6.
Park/neutral position switch
(M/T models)
Refer to
.
7.
Transmission range switch
(CVT models)
Refer to
SYSTEM : Component Parts Loca-
tion"
8.
ECM
Refer to
TROL SYSTEM :
Component Parts Location"
9.
.
10. TCM
SYSTEM : Component Parts Loca-
tion"
11.
Stop lamp switch
Refer to
TROL SYSTEM :
Component Parts Location"
12. Clutch interlock switch
.
13. BCM
SYSTEM : Component Parts Loca-
tion"
14. Power window main switch
(door lock and unlock switch)
15. Front door switch (driver side)
16. Front door lock assembly
17. Back door opener switch
18. Back door request switch
JMKIA6575ZZ
Component Reference
BCM
ECM
IPDM E/R
NATS antenna amp.
TCM (CVT models)
Clutch interlock switch (M/T models)
Revision: 2013 October
2014 JUKE
COMPONENT PARTS
SEC-131
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
BCM
INFOID:0000000009754728
BCM performs the ID verification between BCM and ECM when ignition switch is turned ON.
If the verification result is OK, ECM can start engine. If the verification result is NG, ECM cannot start engine.
ECM
INFOID:0000000009754729
ECM controls the engine.
When power supply position is turned ON, BCM starts communication with ECM and performs the ID verifica-
tion between BCM and ECM.
If the verification result is OK, the engine can start. If the verification result is NG, the engine can not start.
When ECM restarts engine by the Stop/Start System (CVT models), ECM transmits the control signals to
IPDM E/R to crank engine.
IPDM E/R
INFOID:0000000009754730
Starter control relay is integrated in IPDM E/R and used for the engine starting system. Starter control relay is
controlled by IPDM E/R while communicating with ECM. IPDM E/R sends the starter control relay status signal
to ECM.
During engine is running, IPDM E/R controls starter control relay according to the cranking request signal from
ECM for Stop/Start System.
NATS Antenna Amp.
INFOID:0000000009754731
The ID verification is performed between BCM and ignition key via NATS antenna amp. when ignition switch is
turned ON. If an unregistered ID of ignition key is used, the operation of the starting engine is prohibited.
TCM
INFOID:0000000009754732
TCM transmits the shift position signal (P/N position) to IPDM E/R via CAN communication.
IPDM E/R uses shift position signal for the starter control relay control.
Clutch Interlock Switch
INFOID:0000000009754733
Clutch interlock switch detects that clutch pedal is depressed, then provides power source to starter control
relay.
Combination Meter
INFOID:0000000009754734
Combination meter transmits the vehicle speed signal to BCM via CAN communication.
BCM also receives the vehicle speed signal from ABS actuator and electric unit (control unit) via CAN commu-
nication. BCM compares both signals to detect the vehicle speed.
Door Switch
INFOID:0000000009754735
Door switch detects door open/close condition and then transmits ON/OFF signal to BCM.
Combination meter
Door switch
Ignition key
Park/neutral position switch (M/T models)
Remote keyless entry receiver
Security indicator lamp
Starter control relay
Starter relay
Stop lamp switch
Transmission range switch (CVT models)
Component Reference
Revision: 2013 October
2014 JUKE
SEC-132
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
COMPONENT PARTS
Ignition Key
INFOID:0000000009754736
The ID verification is performed between BCM and ignition key via NATS antenna amp. when ignition switch is
turned ON. If an unregistered ID of ignition key is used, the operation of the starting engine is prohibited.
Park/Neutral Position Switch
INFOID:0000000009754737
Park/neutral position switch detects that shift lever is in the neutral position, and then transmits ON/OFF signal
to ECM.
Remote Keyless Entry Receiver
INFOID:0000000009754738
Remote keyless entry receiver receives each button operation signal and electronic key ID signal from Keyfob,
and then transmits the signal to BCM.
Security Indicator Lamp
INFOID:0000000009754739
Security indicator lamp is located on combination meter.
Security indicator lamp blinks when power supply position is in any position except the ON position to warn
that Nissan Anti-Theft System (NATS) is on board.
Starter Control Relay
INFOID:0000000009754740
Starter control relay is integrated in IPDM E/R and used for the engine starting system. Starter control relay is
controlled by IPDM E/R while communicating with ECM. IPDM E/R transmits the starter control relay status
signal to ECM.
During engine is running, starter control relay is controlled by IPDM E/R according to the cranking request sig-
nal from ECM for Stop/Start System.
Starter Relay
INFOID:0000000009754741
Starter relay is integrated in IPDM E/R and controlled by ECM for Stop/Start System.
IPDM E/R transmits starter relay status signal to ECM via CAN communication.
Stop Lamp Switch
INFOID:0000000009754742
Stop lamp switch detects that brake pedal is depressed, and then transmits the signal to BCM.
Transmission Range Switch
INFOID:0000000009754743
Transmission range switch is integrated in CVT assembly to detect the selector lever position, and then trans-
mits the P/N position signal to IPDM E/R.
Revision: 2013 October
2014 JUKE
SYSTEM
SEC-133
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SYSTEM
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS : System Diagram
INFOID:0000000009754744
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS : System Description
INFOID:0000000009754745
SYSTEM DESCRIPTION
NISSAN VEHICLE IMMOBILIZER SYSTEM-NATS [NVIS(NATS)] has the following immobilizer functions:
• NVIS(NATS) shows high anti-theft performance to prevent engine from starting by anyone other than the
owner who has the registered ignition key.
• The ignition key has NVIS(NATS) ID and only ignition key which has the same ID as the ID registered in
BCM and ECM can start engine. This makes high anti-theft performance to prevent the vehicle from being
stolen using a copied ignition key.
• Security indicator lamp always blinks when ignition switch is in any position other than ON. Therefore,
NVIS(NATS) warns outsiders that the vehicle is equipped with the anti-theft system.
• If the system detects a malfunction, security indicator lamp illuminates when ignition switch is turned ON.
• If the owner requires, ignition key ID can be registered for up to 5 keys.
• During trouble diagnosis, when additional ignition key is needed, or when the following components are
replaced, the ID registration is required.
- BCM
- Ignition key
• Possible symptom of NVIS(NATS) malfunction is “Engine cannot start”. The engine also can not be started
because of other than the NVIS(NATS) malfunction, so start the trouble diagnosis according to
• If ECM other than Genuine NISSAN parts is installed, the engine cannot be started. For ECM replacement
EC-561, "Removal and Installation"
.
SECURITY INDICATOR LAMP
• Security indicator lamp is located on combination meter and warns that the vehicle is equipped with NATS.
• Security indicator lamp always blinks, when the ignition switch is in any position other than ON.
• Security indicator lamp turns OFF when the ignition switch is turned ON.
OPERATION WHEN IGNITION KEY IS INSERTED INTO IGNITION KEY CYLINDER
1.
When ignition switch is turned ON, BCM activates NATS antenna amp. to start NVIS(NATS) ID verification
with the ignition key (transponder is integrated).
2.
BCM receives the NVIS(NATS) ID signal from ignition key via NATS antenna amp. and verifies it with the
registered ID.
3.
When the NATS ID verification result is OK, BCM performs the ID verification between BCM and ECM.
4.
When the verification result is OK, BCM transmits the verification OK signal to ECM, and then ECM can
start the engine.
JMKIA6576GB
Revision: 2013 October
2014 JUKE
SEC-134
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
5.
When the ignition switch is turned to the START position, BCM transmits the starter request signal to
IPDM E/R.
VEHICLE SECURITY SYSTEM
VEHICLE SECURITY SYSTEM : System Diagram
INFOID:0000000009754746
VEHICLE SECURITY SYSTEM : System Description
INFOID:0000000009754747
• The vehicle security system has two alarm functions (theft warning alarm and panic alarm), and reduces the
possibility of a theft or mischief by activating horns and headlamps intermittently.
• The panic alarm does not start when the theft warning alarm is activating, and the panic alarm stops when
the theft warning alarm is activated.
The priority of the functions are as per the following.
THEFT WARNING ALARM
• The theft warning alarm function activates horns and headlamps intermittently when BCM detects that any
door is opened by unauthorized means, while the system is in the ARMED state.
• Security indicator lamp on combination meter always blinks when ignition switch is in any position other than
ON. Security indicator lamp blinking warns that the vehicle is equipped with a vehicle security system.
JMKIA6577GB
Priority
Function
1
Theft warning alarm
2
Panic alarm
Revision: 2013 October
2014 JUKE
SYSTEM
SEC-135
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Operation Flow
NOTE:
• BCM ignores the door key cylinder UNLOCK switch signal input for 1 second after the door key cylinder LOCK switch signal input.
• To lock/unlock all doors by operating remote controller button of Keyfob, the Keyfob must be within the detection area of remote key-
less entry receiver. For details, refer to
JMKIA5416GB
No.
System state
Switching condition
1
DISARMED to
PRE-ARMED
When all conditions of A and
one condition of B is satis-
fied.
A
B
• Ignition switch: OFF
• All doors: Closed
All doors are locked by:
• Door key cylinder LOCK switch
• LOCK button of Keyfob
• Door lock and unlock switch
2
PRE-ARMED
to ARMED
When all of the following
conditions are satisfied for
30 seconds.
• Ignition switch: OFF
• All doors: Locked
3
ARMED to
ALARM
When all conditions of A and
B are satisfied.
A
B
Keyfob: Not used
• Any door: Open
4
DISARMED to
PRE-RESET
No conditions.
5
PRE-ARMED
to PRE-RESET
6
ARMED to
PRE-RESET
7
ALARM to
PRE-RESET
8
PRE-RESET to
DISARMED
9
PRE-RESET to
PRE-ARMED
10
PRE-ARMED
to DISARMED
When one of the following
condition is satisfied.
• Ignition switch: ACC/ON
• Door key cylinder UNLOCK switch: ON
• UNLOCK button of Keyfob: ON
• UNLOCK switch of door lock and unlock switch: ON
• Any door: Open
11
ARMED to
DISARMED
When one of the following
condition is satisfied.
• Ignition switch: ACC/ON
• Door key cylinder UNLOCK switch: ON
• UNLOCK button of Keyfob: ON
12
ALARM to
DISARMED
13
RE-ALARM
When the following condition
is satisfied after the ALARM
operation is finished.
• Any door: Open
Revision: 2013 October
2014 JUKE
SEC-136
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
SYSTEM
DISARMED Phase
The vehicle security system is not set in the DISARMED phase. The vehicle security system stays in this
phase while any door is open, because it is assumed that the owner is inside or nearby the vehicle. Security
indicator lamp blinks every 2.4 seconds.
When the vehicle security system is reset, each phase switches to the DISARMED phase directly.
PRE-ARMED Phase
The PRE-ARMED phase is the transient state between the DISARMED phase and the ARMED phase. This
phase is maintained for 30 seconds, so that the owner can reset the setting due to a mis-operation. This phase
switches to the ARMED phase when vehicle conditions are not changed for 30 seconds. Security indicator
lamp illuminates while being in this phase.
To reset the PRE-ARMED phase, refer to the switching condition of No. 10 in the table above.
ARMED Phase
The vehicle security system is set, and BCM monitors all necessary inputs. If any door is opened without using
Keyfob, vehicle security system switches to the ALARM phase. Security indicator lamp blinks every 2.4 sec-
onds.
To reset the ARMED phase, refer to the switching condition of No. 11 in the table above.
ALARM Phase
BCM transmits “Theft Warning Horn Request” signal and “High Beam Request” signal intermittently to IPDM
E/R via CAN communication. In this phase, horns and headlamps are activated intermittently for approxi-
mately 50 seconds to warn that the vehicle is accessed by unauthorized means. ON/OFF timing of horns and
headlamps are synchronized. After 50 seconds, the vehicle security system returns to the ARMED phase. At
this time, if BCM still detects unauthorized access to the vehicle, the system is switched to the ALARM phase
again. This RE-ALARM operation is carried out a maximum of 2 times.
To cancel the ALARM operation, refer to the switching condition of No. 12 in the table above.
NOTE:
If a battery terminal is disconnected during the ALARM phase, theft warning alarm stops. But when the battery
terminal is reconnected, theft warning alarm is activated again.
PRE-RESET Phase
The PRE-RESET phase is the transient state between each phase and DISARMED phase.
PRE-ARMED phase is not available for this models.
PANIC ALARM
• The panic alarm function activates horns and headlamps intermittently when the owner presses the PANIC
ALARM button of Keyfob outside the vehicle while the ignition switch is OFF.
• When BCM receives panic alarm signal from Keyfob, BCM transmits “Theft Warning Horn Request” signal
and “High Beam Request” signal intermittently to IPDM E/R via CAN communication. To prevent the activa-
tion due to mis-operation of Keyfob by owner, the panic alarm function is activated when BCM receives the
signal for 0.4 - 0.6 seconds.
• Panic alarm operation is maintained for 25 seconds.
• Panic alarm operation is cancelled when BCM receives one of the following signals.
- LOCK button of Keyfob: ON
- UNLOCK button of Keyfob: ON
- PANIC ALARM button of Keyfob: Long pressed
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM)
SEC-137
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000009754748
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT)
INFOID:0000000009754749
WORK SUPPORT
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2013 October
2014 JUKE
SEC-138
< SYSTEM DESCRIPTION >
[WITHOUT INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000009754750
WORK SUPPORT
ACTIVE TEST
PANIC ALARM
PANIC ALARM : CONSULT Function (BCM - PANIC ALARM)
INFOID:0000000009754751
ACTIVE TEST
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.
VEHICLE SECURITY HORN
This test is able to check horn operation. Horn will be activated for 0.5 seconds after “ON” on
CONSULT screen is touched.
HEADLAMP (HI)
This test is able to check headlamp (HI) operation. Headlamps (HI) will be activated for 0.5
seconds after “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation. Hazard warning lamps will be acti-
vated after “LH” or “RH” on CONSULT screen is touched.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation. Security indicator lamp will be
turned on when “ON” on CONSULT screen is touched.
Test item
Description
VEHICLE SECURITY HORN
This test is able to check horn operation.
Horn is activated for 0.5 seconds after “ON” on CONSULT screen touched.
HEAD LAMP (HI)
This test is able to check headlamp (HI) operation.
Headlamps (HI) will be activated after “ON” on CONSULT screen touched.
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст