Nissan Juke (2014 year). Service Repair Manual — part 130
EXL-104
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
LIGHTING & TURN SIGNAL SWITCH
LIGHTING & TURN SIGNAL SWITCH
Removal and Installation
INFOID:0000000009754553
REMOVAL
Remove light & turn signal switch. Refer to
BCS-91, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
Revision: 2013 October
2014 JUKE
HAZARD SWITCH
EXL-105
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000009754554
Removal and Installation
INFOID:0000000009754555
REMOVAL
1.
Remove audio unit. Refer to
AV-68, "Removal and Installation"
2.
Disengage fixing pawls, and then remove hazard switch from instrument panel inside to outside.
INSTALLATION
Install in the reverse order of removal.
1.
Instrument panel assembly
2.
Hazard switch
: Pawl
JMLIA1246ZZ
Revision: 2013 October
2014 JUKE
EXL-106
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
SIDE TURN SIGNAL LAMP
SIDE TURN SIGNAL LAMP
Exploded View
INFOID:0000000009754556
Removal and Installation
INFOID:0000000009754557
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the side turn signal lamp in numerical order shown in
the figure.
2.
Rotate the bulb socket counterclockwise and unlock it.
NOTE:
Support side turn signal lamp harness with tape so that it won't fall
into the front fender.
INSTALLATION
1.
Rotate the bulb socket clockwise and lock it.
2.
Fix the pawl-side behind the side turn signal lamp housing first, then push the resin clip-side.
Replacement
INFOID:0000000009754558
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
SIDE TURN SIGNAL LAMP BULB
1.
Remove side turn signal lamp. Refer to
EXL-106, "Removal and Installation"
.
2.
Remove bulb from the bulb socket.
1.
Side turn signal lamp bulb
2.
Side turn signal lamp housing
JMLIA1241ZZ
: Vehicle front (side turn signal lamp LH)
: Vehicle rear (side turn signal lamp RH)
JMLIA1302ZZ
Revision: 2013 October
2014 JUKE
HEADLAMP AIMING SWITCH
EXL-107
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP AIMING SWITCH
Exploded View
INFOID:0000000009754559
Removal and Installation
INFOID:0000000009754560
REMOVAL
1.
Remove instrment lower panel assembly LH. Refer to
IP-13, "Removal and Installation"
2.
Remove headlamp aiming switch fixing clips, and then remove headlamp aiming switch from instrument
lower panel assembly LH.
INSTALLATION
Install in the reverse order of removal.
1.
Headlamp aiming switch
2.
Instrument lower panel assembly LH
: Pawl
JMLIA1442ZZ
Revision: 2013 October
2014 JUKE
EXL-108
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000009754561
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000009754562
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Full open back door.
1.
Grommet
2.
Grommet
3.
Rear combination lamp
: Clip
: N·m (kg-m, in-lb)
JMLIA1217GB
1.
Rear combination lamp housing assembly 2.
Back-up lamp bulb
3.
Harness connector
4.
Rear turn signal/tail lamp bulb
5.
Stop lamp bulb
JMLIA1218ZZ
Revision: 2013 October
2014 JUKE
REAR COMBINATION LAMP
EXL-109
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2.
Remove luggage side lower finisher. Refer to
INT-35, "LUGGAGE SIDE LOWER FINISHER : Removal
3.
Remove rear combination lamp mounting bolts.
4.
Insert a remover tool into the rear combination lamp rear fender to disengage the clips.
5.
Pull up rear combination lamp, and then remove rear combination lamp.
6.
Disconnect rear combination lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000009754563
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
REAR TURN SIGNAL/TAIL LAMP BULB
1.
Remove rear combination lamp assembly. Refer to
EXL-108, "Removal and Installation"
.
2.
Rotate rear turn signal/tail lamp bulb socket counterclockwise, and then remove rear turn signal/tail lamp
bulb socket.
3.
Remove rear turn signal/tail lamp bulb from rear turn signal/tail lamp bulb socket.
STOP LAMP BULB
1.
Remove rear combination lamp assembly. Refer to
EXL-108, "Removal and Installation"
.
2.
Rotate stop lamp bulb socket counterclockwise, and then remove stop lamp bulb socket.
3.
Remove stop lamp bulb from stop lamp bulb socket.
BACK-UP LAMP BULB
1.
Remove rear combination lamp assembly. Refer to
EXL-108, "Removal and Installation"
.
2.
Rotate back-up lamp bulb socket counterclockwise, and then remove back-up lamp bulb socket.
3.
Remove back-up lamp bulb from back-up lamp bulb socket.
Revision: 2013 October
2014 JUKE
EXL-110
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HIGH-MOUNTED STOP LAMP
HIGH-MOUNTED STOP LAMP
Exploded View
INFOID:0000000009754564
NISMO MODELS
EXCEPT NISMO MODELS
Removal and Installation
INFOID:0000000009754565
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
NISMO MODELS
1.
Remove rear spoiler. Refer to
EXT-46, "Removal and Installation"
.
2.
Remove high-mounted stop lamp cover mounting bolts and remove the cover.
1.
Rear spoiler
2.
High-mounted stop lamp
3.
High-mounted stop lamp cover
JMLIA3757ZZ
1.
High-mounted stop lamp
2.
Seal packing
: N·m (kg-m, in-lb)
JMLIA1220GB
Revision: 2013 October
2014 JUKE
HIGH-MOUNTED STOP LAMP
EXL-111
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
3.
Remove high-mounted stop lamp harness connector from rear spoiler.
4.
Pull out high-mounted stop lamp, and then remove high-mounted stop lamp.
EXCEPT NISMO MODELS
1.
Remove blind seal from back door inside.
CAUTION:
Be careful not to damage the blind seal, so that it can be reused.
2.
Remove high-mounted stop lamp mounting nuts and harness connector.
3.
Pull high-mounted stop lamp toward vehicle upside, and then remove high-mounted stop lamp.
INSTALLATION
Note the following item and then, install in the reverse order of removal.
CAUTION:
Seal packing cannot be reused.
Revision: 2013 October
2014 JUKE
EXL-112
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
LICENSE PLATE LAMP
LICENSE PLATE LAMP
Exploded View
INFOID:0000000009754566
Removal and Installation
INFOID:0000000009754567
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
While pressing the license plate lamp to direction right side, pull
it to direction outside and then remove it.
2.
Disconnect license plate lamp connector.
INSTALLATION
Install in the reverse order of removal.
Replacement
INFOID:0000000009754568
CAUTION:
• Disconnect the battery negative terminal or the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
LICENSE PLATE LAMP BULB
1.
Remove license plate lamp.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the socket.
1.
License plate lamp housing assembly
2.
Bulb
3.
License plate lamp bulb socket
: Pawl
JMLIA1219ZZ
JPLIA0364ZZ
Revision: 2013 October
2014 JUKE
REAR FOG LAMP
EXL-113
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REAR FOG LAMP
Exploded View
INFOID:0000000009754569
REMOVAL
Removal and Installation
INFOID:0000000009754570
CAUTION:
Disconnect battery negative terminal or remove the fuse.
REMOVAL
1.
Remove rear bumper fascia lower. Refer to
EXT-20, "Removal and Installation"
2.
Remove rear fog lamp housing mounting nuts.
3.
Remove rear fog lamp housing from the rear bumper fascia lower.
4.
Remove rear fog lamp housing bracket from rear bumper fascia lower.
INSTALLATION
Installation is the reverse order of removal.
1.
Rear fog lamp housing
2.
Rear bumper fascia lower
3.
Rear fog lamp housing bracket
N·m (kg-m, in-lb)
: Vehicle front
JMLIA3677GB
Revision: 2013 October
2014 JUKE
EXL-114
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
REAR REFLEX REFLECTOR
REAR REFLEX REFLECTOR
Exploded View
INFOID:0000000009754571
Removal and Installation
INFOID:0000000009754572
REMOVAL
1.
Remove rear bumper fascia lower. Refer to
EXT-20, "Removal and Installation"
2.
Disengage rear reflex reflector fixing metal clip and then remove
rear reflex reflector according to the numerical order 1
→
3 as
shown in the figure.
INSTALLATION
Install in the reverse order of removal.
1.
Rear bumper fascia lower
2.
Rear reflex reflector RH
3.
Rear reflex reflector LH
: Metal clip
: Vehicle front
JMLIA3679ZZ
JMLIA3680ZZ
Revision: 2013 October
2014 JUKE
SERVICE DATA AND SPECIFICATIONS (SDS)
EXL-115
< SERVICE DATA AND SPECIFICATIONS (SDS)
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Bulb Specifications
INFOID:0000000009754573
Item
Type
Wattage (W)
Headlamp (HI/LO)
HB5
65/55
Front combination lamp
Front turn signal lamp
PY21W (Amber)
21
Parking lamp
WY5W (Amber)
5
Front marker lamp
12V3.8W
3.8
Front fog lamp
H8
35
Side turn signal lamp
WY5W (Amber)
5
Rear combination lamp
Rear turn signal lamp/Tail lamp
W21/5W
21/5
Stop lamp
W21W
21
Back-up lamp
W16W
16
License plate lamp
W5W
5
High-mounted stop lamp
LED
—
Revision: 2013 October
2014 JUKE
EXT-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
D
E
F
G
H
I
J
L
M
SECTION
EXT
A
B
EXT
N
O
P
CONTENTS
EXTERIOR
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing of Battery Terminal . .....
Precaution for Procedure without Cowl Top Cover
. ..
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tools . . . . . . . . . . . ..
Commercial Service Tools . . . . . . . . . ....
SYMPTOM DIAGNOSIS . . . . . . . ...
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES . . . . . . . . . . . . . . . .
Work Flow . . . . . . . . . . . . . . . .....
Inspection Procedure . . . . . . . . . . . ....
Diagnostic Worksheet . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
FRONT BUMPER . . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR BUMPER . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FRONT GRILLE . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
COWL TOP . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FENDER PROTECTOR . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
SILL COVER . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FLOOR SIDE FAIRING . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
FILLET MOLDING . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
FRONT FILLET MOLDING . . . . . . . . . .
FRONT FILLET MOLDING : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
REAR FILLET MOLDING . . . . . . . . . . ..
REAR FILLET MOLDING : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
ROOF SIDE MOLDING . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
DOOR OUTSIDE MOLDING . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
FRONT DOOR OUTSIDE MOLDING . . . . . .
FRONT DOOR OUTSIDE MOLDING : Removal
and Installation . . . . . . . . . . . . . .
REAR DOOR OUTSIDE MOLDING . . . . . . ...
REAR DOOR OUTSIDE MOLDING : Removal
and Installation . . . . . . . . . . . . . .
DOOR SASH TAPE . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . . .
FRONT DOOR SASH TAPE . . . . . . . . . ..
FRONT DOOR SASH TAPE : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
REAR DOOR SASH TAPE . . . . . . . . . .
Revision: 2013 October
2014 JUKE
EXT-2
REAR DOOR SASH TAPE : Removal and Instal-
lation . . . . . . . . . . . . . . . . . ...
REAR FENDER COVER . . . . . . . . .
Exploded View . . . . . . . . . . . . . ....
Removal and Installation . . . . . . . . . ....
BACK DOOR FINISHER . . . . . . . . ...
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
REAR SPOILER . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Revision: 2013 October
2014 JUKE
PRECAUTIONS
EXT-3
< PRECAUTION >
C
D
E
F
G
H
I
J
L
M
A
B
EXT
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009750207
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing of Battery Terminal
INFOID:0000000010138834
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
Revision: 2013 October
2014 JUKE
EXT-4
< PRECAUTION >
PRECAUTIONS
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009750208
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
PIIB3706J
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст