Nissan Juke (2014 year). Service Repair Manual — part 129
EXL-88
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
Description
INFOID:0000000009754526
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure
INFOID:0000000009754527
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL HI REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
ON
LO
OFF
Revision: 2013 October
2014 JUKE
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
EXL-89
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000009754528
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009754529
1.
CHECK COMBINATION SWITCH
Check the combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “HL LO REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
BCS-90, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
ON
OFF
OFF
Revision: 2013 October
2014 JUKE
EXL-90
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS ARE NOT
TURNED ON
Description
INFOID:0000000009754530
The parking, license plate, tail, rear side marker lamps and each illumination are not turned ON in any condi-
tion.
Diagnosis Procedure
INFOID:0000000009754531
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the item status normal?
YES
>> Replace IPDM E/R.
NO
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
Monitor item
Condition
Monitor status
TAIL & CLR REQ
Lighting switch
1ST
ON
OFF
OFF
Revision: 2013 October
2014 JUKE
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
EXL-91
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON
Description
INFOID:0000000009754532
The front fog lamps are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000009754533
1.
CHECK FUSE
Check that the following fuse is fusing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the applicable circuit. And then replace the fuse.
2.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning part.
3.
CHECK FRONT FOG LAMP REQUEST SIGNAL INPUT
CONSULT DATA MONITOR
1.
Select “FR FOG REQ” of IPDM E/R data monitor item.
2.
With operating the front fog lamp switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
BCS-90, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
Unit
Location
Fuse No.
Capacity
Front fog lamp
Fuse and fusible link block
#50
15 A
Monitor item
Condition
Monitor status
FR FOG REQ
Front fog lamp switch
(With lighting switch 1ST)
ON
ON
OFF
OFF
Revision: 2013 October
2014 JUKE
EXL-92
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
HEADLAMP AIMING ADJUSTMENT
PERIODIC MAINTENANCE
HEADLAMP AIMING ADJUSTMENT
Description
INFOID:0000000009754534
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
JMLIA1338ZZ
A
Headlamp RH (UP/DOWN) adjustment screw B.
Headlamp LH (UP/DOWN) adjustment screw
: Vehicle center
Adjustment screw
Screw driver rotation
Facing direction
A
Headlamp RH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
Revision: 2013 October
2014 JUKE
HEADLAMP AIMING ADJUSTMENT
EXL-93
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Aiming Adjustment Procedure
INFOID:0000000009754535
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the headlamp center and the screen.
3.
Start the engine. Turn the headlamp (LO) ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Measure the distance (X) between the horizontal center line of headlamp (H) and the cutoff line (A) within
the light axis measurement range (R) from the vertical center line ahead of headlamp (V).
Low beam distribution on the screen
5.
Adjust the cutoff line height (X) with the aiming adjustment screw so as to enter in the adjustment range
(M–N) according to the horizontal center line of headlamp (H).
unit: mm (in)
Side view
B
Headlamp LH (UP/DOWN)
Clockwise
DOWN
Counterclockwise
UP
Adjustment screw
Screw driver rotation
Facing direction
Light axis measurement range (R)
: 350
±
175 mm (13.78
±
6.89 in)
JSLIA0005ZZ
Horizontal center line of headlamp (H)
Highest cutoff line height (M)
Lowest cutoff line height (N)
700 (27.56) or less
4 (0.16)
30 (1.18)
701(27.60) – 800 (31.50)
4 (0.16)
30 (1.18)
801 (31.54) or more
17 (0.67)
44 (1.73)
JSLIA0006ZZ
Distance between the headlamp center and the screen (L)
: 10 m (32.8 ft)
Revision: 2013 October
2014 JUKE
EXL-94
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
FRONT FOG LAMP AIMING ADJUSTMENT
FRONT FOG LAMP AIMING ADJUSTMENT
Description
INFOID:0000000009754536
PREPARATION BEFORE ADJUSTING
NOTE:
• For details, refer to the regulations in your own country.
• Perform aiming if the vehicle front body has been repaired and/or the headlamp assembly has been
replaced.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehicle condition. (Remove luggage from the passenger compartment and the trunk
room.)
NOTE:
Do not remove the temporary tire, jack and on-vehicle tool.
• Wipe out dirt on the headlamp.
CAUTION:
Never use organic solvent (thinner, gasoline etc.)
• Ride alone on the driver seat.
AIMING ADJUSTMENT SCREW
• Turn the aiming adjusting screw for adjustment.
• For the position and direction of the adjusting screw, refer to the
figure.
NOTE:
A screwdriver or hexagonal wrench [6 mm (0.24 in)] can be used
for adjustment.
Aiming Adjustment Procedure
INFOID:0000000009754537
1.
Place the screen.
NOTE:
• Stop the vehicle facing the wall.
• Place the board on a plain road vertically.
2.
Face the vehicle with the screen. Maintain 10 m (32.8 ft) between the front fog lamp center and the
screen.
3.
Start the engine. Turn the front fog lamp ON.
NOTE:
Shut off the headlamp light with the board to prevent from illuminating the adjustment screen.
CAUTION:
Never cover the lens surface with a tape etc. The lens is made of resin.
4.
Adjust the cutoff line height (A) with the aiming adjustment screw so that the distance (X) between the hor-
izontal center line of front fog lamp (H) and (A) becomes 150 mm (5.91 in).
A: UP
B: DOWN
JMLIA1249ZZ
Revision: 2013 October
2014 JUKE
FRONT FOG LAMP AIMING ADJUSTMENT
EXL-95
< PERIODIC MAINTENANCE >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Front fog lamp light distribution on the screen
JPLIA0008ZZ
A
: Cutoff line
B
: High illuminance area
H
: Horizontal center line of front fog lamp
V
: Vertical center line of front fog lamp
X
: Cutoff line height
Revision: 2013 October
2014 JUKE
EXL-96
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
HEADLAMP
REMOVAL AND INSTALLATION
HEADLAMP
Exploded View
INFOID:0000000009754538
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000009754539
CAUTION:
Disconnect the battery negative terminal or the fuse.
REMOVAL
1.
Headlamp assembly
: N·m (kg-m, in-lb)
JMLIA1768GB
1.
Headlamp housing assembly
2.
Cap
3.
Halogen bulb
4.
Bulb holder
JMLIA1317ZZ
Revision: 2013 October
2014 JUKE
HEADLAMP
EXL-97
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1.
Remove front bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
2.
Remove headlamp mounting bolts.
3.
Pull out the headlamp assembly forward the vehicle, and then disconnect the connector before removing
the headlamp assembly.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000009754540
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1.
Disconnect headlamp bulb connector.
2.
Remove bulb holder.
3.
Remove halogen bulb from the headlamp housing assembly.
Disassembly and Assembly
INFOID:0000000009754541
DISASSEMBLY
1.
Remove back cover.
2.
Remove bulb holder.
3.
Remove halogen bulb from the headlamp housing assembly.
ASSEMBLY
Note the following item, and then assemble in the reverse order of disassembly.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
Revision: 2013 October
2014 JUKE
EXL-98
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
FRONT COMBINATION LAMP
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000009754542
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000009754543
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Front combination lamp
: N·m (kg-m, in-lb)
JMLIA1236ZZ
1.
Parking lamp bulb
2.
Parking lamp bulb socket
3.
Front marker lamp bulb socket
4.
Front marker lamp bulb
5.
Front turn signal lamp bulb socket
6.
Front turn signal lamp bulb
7.
Front combination lamp housing
JMLIA1318ZZ
Revision: 2013 October
2014 JUKE
FRONT COMBINATION LAMP
EXL-99
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
1.
Remove front bumper fascia. Refer to
EXT-15, "Removal and Installation"
.
2.
Remove front combination lamp mounting bolts and nut.
3.
Pull out front combination lamp assembly forward the vehicle, and then disconnect the connector before
removing the headlamp assembly.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
Interference of front combination lamp lens with front fender may cause intrusion of water into front
combination lamp or rusting of fender due to damage of painted surface. Be careful to operate without
allowing parts to interfere with each other.
Replacement
INFOID:0000000009754544
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
PARKING LAMP BULB
1.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
2.
Remove parking lamp bulb from the bulb socket.
FRONT MARKER LAMP BULB
1.
Rotate the front marker lamp bulb socket counterclockwise and unlock it.
2.
Remove the front marker lamp bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
2.
Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.
Disassembly and Assembly
INFOID:0000000009754545
DISASSEMBLY
1.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
2.
Remove parking lamp bulb from the bulb socket.
3.
Rotate the front marker lamp bulb socket counterclockwise and unlock it.
4.
Remove the front marker lamp bulb from the bulb socket.
5.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
6.
Remove front turn signal lamp bulb from the front turn signal lamp bulb socket.
ASSEMBLY
Note the following item and then, install in the reverse order of removal.
CAUTION:
After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
Revision: 2013 October
2014 JUKE
EXL-100
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
DAYTIME RUNNING LIGHT
DAYTIME RUNNING LIGHT
Exploded View
INFOID:0000000009754546
Removal and Installation
INFOID:0000000009754547
CAUTION:
Disconnect the battery negative terminal or remove the fuse to prevent electric leakage.
REMOVAL
1.
Remove front bumper fascia lower. Refer to
EXT-15, "Removal and Installation"
.
2.
Disconnect daytime running light harness connector.
3.
Remove daytime running light mounting nuts.
4.
Remove daytime running light from front bumper fascia lower.
INSTALLATION
Install in the reverse order of removal.
1.
Daytime running light
2.
Front bumper fascia assembly
3.
U nut
4
Harness connector assembly
N·m (kg-m, in-lb)
JMLIA3676GB
Revision: 2013 October
2014 JUKE
FRONT FOG LAMP
EXL-101
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT FOG LAMP
Exploded View
INFOID:0000000009754548
Removal and Installation
INFOID:0000000009754549
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove fender protector. Keep the service area. Refer to
EXT-27, "Removal and Installation"
.
2.
Disconnect front fog lamp harness connector.
3.
Remove front fog lamp bracket.
4.
Remove front fog lamp mounting bolt, and then remove front fog lamp from front fog lamp bracket.
INSTALLATION
Note the following item, and then installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000009754550
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove fender protector. Keep the service area. Refer to
EXT-27, "Removal and Installation"
.
1.
Front fog lamp assembly
2.
Metal clip
3.
Front fog lamp bulb
4.
Front fog lamp bracket
5.
U nut
6.
Front bumper fascia lower
: N·m (kg-m, in-lb)
JMLIA1240GB
Revision: 2013 October
2014 JUKE
EXL-102
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
FRONT FOG LAMP
2.
Remove front fog lamp bulb connector (1).
3.
Rotate the bulb (2) counterclockwise and unlock it.
JPLIA0345ZZ
Revision: 2013 October
2014 JUKE
OPTICAL SENSOR
EXL-103
< REMOVAL AND INSTALLATION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
OPTICAL SENSOR
Exploded View
INFOID:0000000009754551
Removal and Installation
INFOID:0000000009754552
REMOVAL
1.
Insert an appropriate tool between the switch panel and the instrument upper panel. Pull out the optical
sensor upward.
2.
Disconnect the optical sensor connector.
3.
Remove optical sensor from switch panel.
INSTALLATION
Install in the reverse order of removal.
1.
Optical sensor
2.
Switch panel
: Pawl
JMLIA1245ZZ
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст